Fujitsu 2300 manual Resuming System Operation

Page 27

•If the battery pack charge drops to the Low-Battery Warning level while the system is running, the system will beep periodically. If this occurs, suspend system operation, shut down the system, or attach an external power source, such as the AC adapter, to the pen tablet.

•If the battery charge drops to the Critically Low level while the system is running, the system is forced into Suspend-to-RAM mode. If this occurs, you must either install a charged battery pack, or connect an appropriate external power source such as the AC adapter before you can resume system operation. (If the battery charge drops to the Critically Low level while the system is in Suspend-to-RAM mode, the system stays in Suspend-to-RAM mode.)

•Suspending system operation interrupts data communications; however, some programs may block the system from suspending to prevent an interruption.

•The Suspend/Resume button on your system may be disabled. If this is the case, pressing the Suspend/Resume button may not suspend system operation as described here. Contact your local help desk or reseller if your system configuration is not suitable.

•The Suspend/Resume button on your system may be programmed to act as an On/Off switch. If this is the case, all active data will be lost if this button is pressed. In order to ensure that all active data is saved prior to turning off the system, exit Windows by choosing Shut Down from the Start menu and carry out the Shut Down command; this also turns off the system.

•If your system is equipped with a PC Card that allows you to connect to a wired or wireless network, you may be logged off the network after a period of inactivity while system operation is suspended. Contact your network administrator or local help desk for details on log-off parameters for your network.

Resuming System Operation

To resume system operation, (from either Suspend-to-RAM or Suspend-to-Disk modes), press the Suspend/Resume button.

•From Suspend-to-RAM mode

After a few seconds, the system returns to the Fully On state and system operation resumes. Note that the display turns on shortly before the pen becomes active due to the power-up sequences observed by the system.

•From Suspend-to-Disk mode

Active data is read from the hard disk drive, and after 15 to 30 seconds, the system returns to the Fully On state.

2-6

Using the Stylistic 2300 Pen Tablet

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Page Page Page Copyright Fujitsu Personal Systems, Inc Page UL Notices Agency ComplianceFCC Notices AddressTelephone Table of Contents Appendix a Agency Notices Included with the Stylistic 2300 Pen Tablet Getting StartedOptional Accessories Front Features Stylistic 2300 Pen Tablet FeaturesStylistic 2300 Pen Tablet Features Front View Stylistic 2300 Pen Tablet Features Rear View System Status Indications Status DisplayStatus Display Peripheral Connectors Connectors and Peripheral InterfacesFDD Connector Connector Pen Tablet Icon Purpose Connector Pen Tablet Icon Purpose Peripheral Getting Started System States Using the Stylistic 2300 Pen TabletChanging System States Off state Starting the Pen Tablet Suspending System Operation Shutting Down the SystemPower icon is not displayed Suspend-to-Diskmode Power icon is blinking Suspend-to-RAMmodeResuming System Operation Speaker Mute hotpad Using HotpadsVolume hotpads Programmable hotpadBrightness hotpads Using the PenDisplay Select hotpad Contrast hotpadsStylistic 2300 Pen Battery Pack Charging Time Charging the Battery PackRemoving and Installing the Battery Pack Removing and Installing the Battery Pack Conserving Battery PowerModem Connection Care of Bridge BatteryPC Card Slots PC Card SlotsProtecting the Display Screen Care and MaintenanceStoring the Stylistic 2300 Pen Tablet Avoiding Overheating Cleaning the Display ScreenReplacing the Pen Tip Replacing the Pen TipOpening the Pen Replacing the Pen BatteryCalibrating the Pen Calibrating the Pen System Will Not Resume Operation Solving ProblemsInfrared Data Transfer Is Not Working Configuring Peripherals Interfaces Agency Notices 2Appendix DOC Industry Canada Compliance Notices Avis Aux Utilisateurs Du Réseau Téléphonique Canadien Avertissement 6Appendix Index-1 IndexIndex-2 Index-3 Index-4
Top Page Image Contents