Dukane 28A8945, 28A9058 manual Basic Operation, Turning on / OFF Projector, Turning on Projector

Page 21
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
When Power Management function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on pages 39 and 40.
When WARNING TEMP. indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on projector again.
When WARNING TEMP. indicator continues to flash, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF and disconnect AC Power Cord from an AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 43.)
4. Turn a projector on again.
If WARNING TEMP. indicator should still continue to flash, contact sales dealer where you purchased this projector or service center.

BASIC OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

before turning on projector. (Refer to "CONNECTING TO

 

PROJECTOR" on Pages 12~15 for connecting that equipment.)

2

Connect a projector's AC Power Cord into a wall outlet and turn

MAIN ON / OFF SWITCH to ON. LAMP indicator lights RED,

 

and READY indicator lights GREEN.

3

Press POWER ON-OFF button on Top Control or on Remote

Control Unit to ON. LAMP indicator dims, and Cooling Fans start

to operate. Preparation Display appears on a screen and count- down starts. Signal from source appears after 30 seconds. Current Input position and Lamp status are also displayed on screen for 5 seconds. (Refer to "LAMP MANAGEMENT" on page 44.)

LAMP STATUS

INPUT 1

1 2

30

Preparation Display disappears after 30 seconds.

E

TURNING OFF PROJECTOR

1

Press power ON-OFF button on Top Control or on Remote

 

 

 

 

Control Unit, and a message "Power off?" appears on a screen.

 

 

 

 

2

Press power ON-OFF button again to turn off projector. LAMP

 

 

 

 

 

indicator lights bright and READY indicator turns off. After

 

 

Power off?

 

 

approximate 90 seconds, READY indicator will light green again

 

 

 

 

 

 

 

 

 

 

and projector may be turned on by pressing power ON-OFF

 

 

 

 

 

button.

 

 

 

 

3

Cooling fans will operate for approximate 2 minutes after projec-

 

 

 

 

Message disappears after 4 seconds.

tor is turned off. To power down completely, turn MAIN ON/OFF

 

 

 

 

SWITCH to OFF and disconnect AC Power Cord.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Models 28A8945/9058 To the Owner Voor de klanten in Nederland Safety InstructionsUL, CUL, TUV, NOM, Iram CompliancesTable of Contents Compatibility Features and DesignName of Each Part of Projector PreparationSETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Preparation Lens Installation Lens Shift AdjustmentPositioning Projector Moving Projector Preparation Picture Level and Tilt AdjustmentConnecting Projector Replacement of TerminalTerminals of Projector Input 1, 2 Connecting Projector INPUT/OUTPUT Terminals and Jacks InputAudio Output Jacks Terminals Projector Connecting to Computer2INPUT Terminals of a Projector Connecting to Video EquipmentBefore Operation TOP Controls and IndicatorsLaser Pointer Function Operation of Remote ControlRemote Control Batteries Installation HOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Screen Menu Before Operation Menu BARTurning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorZoom Adjustment Adjusting ScreenFocus Adjustment Keystone AdjustmentTimer Function Basic Operation Picture Freeze FunctionBlank Function Direct Operation Sound AdjustmentMenu Operation Sound MenuSelecting Input Source Computer InputSelecting Computer System InputSelect Computer System Manually Computer Input Automatic MULTI-SCAN SystemAuto PC System MenuResolution Computer Input Compatible Computer SpecificationsAuto PC Adjustment PC AdjustmentPC Adjust Menu Computer InputComputer Input Manual PC Adjustment Display area Display area HFull screen Image Level Select Direct Picture Image AdjustmentImage Level Select Menu Image Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Input When Select Input 3 AV TerminalVideo Input Selecting Video SystemAuto AV System Menu Video or S-VIDEOCinema Color Video Input Image Level AdjustmentTint Noise reductionReset Reset all adjustment to previous figure Quit Setting Setting MenuSetting Menu To change code of Projector To change code of Remote Control UnitWireless Mouse mode Projector modeLamp counter reset Maintenance Operating Wireless MouseInstallation Operating Wireless MouseCleaning Projection Lens Appendix AIR Filter Care and CleaningYellow Lamp Dim Lamp Red Lamp Mark on Lamp Appendix Lamp ManagementOrder Replacement Lamp Appendix Lamp ReplacementTroubleshooting Wireless Mouse Remote Control UnitDoes not work Function does notTechnical Specifications DVI-I Terminal DIGITAL/ANALOG Appendix Configurations of TerminalsLamp Replacement Service & Repair Policy & Procedure FIVE-YEAR Limited WarrantyAudio Visual Products
Top Page Image Contents