Dukane 28A8751 Installation of the Projector and Screen, Angle Adjustment, Side View

Page 15

INSTALLATION

Installation of the Projector and Screen

Refer to the drawing and table below for determining the screen size and projection distance.

ENGLISH

The projection distances shown in the table below are for full size.

a: Distance from the projector to the screen. (±10%)

b: Distance from the lens center to the bottom of the screen. (±10%)

Table 1. Installation Reference

Screen size

 

a [inches (m)]

 

b

[inches (m)]

Min.

Max.

[inches (cm)]

 

 

 

 

 

 

 

 

40

(1.0)

37

(0.9)

46

(1.2)

3

(8.7)

 

 

 

 

 

 

 

 

60

(1.5)

57

(1.5)

69

(1.8)

5

(13.1)

 

 

 

 

 

 

 

 

80

(2.0)

77

(1.9)

93

(2.4)

7

(17.4)

 

 

 

 

 

 

 

 

100

(2.5)

96

(2.4)

116

(2.9)

9

(21.8)

 

 

 

 

 

 

 

 

120

(3.0)

116

(2.9)

139

(3.5)

10

(26.1)

 

 

 

 

 

 

 

 

150

(3.8)

145

(3.7)

174

(4.4)

13

(32.7)

 

 

 

 

 

 

 

 

200

(5.0)

194

(4.9)

233

(5.9)

17

(43.5)

 

 

 

 

 

 

 

 

Screen

TOP VIEW

Lens center

b

aSIDE VIEW

CAUTION • Install the projector in a suitable environment according to instructions of the accompanying manual “SAFETY INSTRUCTIONS” and this manual.

Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and cause damage. Be especially careful not to install it with ventilation holes blocked.

Do not install LCD projector in smoke effected environment. Smoke residue may buildup on critical parts (i.e.LCD panel, Lens Assy etc.).

Angle Adjustment

Use the foot adjusters on the bottom of the projector to adjust the projection angle. It is variable within 0˚ to 10˚ approximately.

1.Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection angle.

2.Release the button to lock at the desired angle.

3.Make the rear foot adjuster screw to adjust the left-right slope.

Foot Adjuster

Press the foot adjuster button Rear Foot Adjuster

CAUTION • Do not release the foot adjuster button unless the projector is being held; otherwise, the projector could overturn or fingers could get

caught and cause personal injury.

ENGLISH-5

Image 15
Contents 28A8751 Page Page Page Page Page Page Page Page Page Contents Features Contents of packageBefore USE Rear / Right View Before USEPart Names Front / Left ViewReplacing Remote ControllerLoading the Batteries First LoadingInstallation Reference InstallationInstallation of the Projector and Screen Angle AdjustmentInstallation CablingCabling Power Connection Example of system setupPlug & Play Standby Power onPower OFF OperationsOperations Basic OperationBasic Operation Description Normal menu Single menu Set/Clear Mute Mode Press the Mute buttonAutomatic Adjustment at RGB Input Press the Auto button Automatic Adjustment at Video Input Press the Auto buttonSelect Position of Image Setup MenuSetup Menu Select Image Aspect RatioInput Menu Input MenuImage Menu Description Setup Initial Screen Display Select Turn on withSelect Color Temperature Image MenuSelect Menu Display Language Select with Options MenuOptions Menu Description Select Menu Background Color Select withSelect Blank Screen Color Select the color with No Signal MenuNo Signal Menu Setup Initial Screen Display Select the Turn on withLamp Life MaintenanceLamp LampMaintenance Resetting the Lamp TimerReplacing the Lamp Cleaning the Lens Air Filter MaintenanceOther Maintenance Maintenance Inside the EquipmentOSD Messages TroubleshootingMessage Contents OSD MessageIndicator TroubleshootingIndicators Message Indicators MessageSymptom SymptomSymptom Possible cause Remedy Specifications SpecificationsWarranty and AFTER-SERVICE Page Mini Din 4-pin Connector S-VIDEO Dimension DiagramSignal Connector Pin Assignment Sub 15-pin Shrink Connector RGBTechnical Example of computer signalMac 13mode Initial set signalsConnection to the Mouse Control Protocol Communications settingCommand data RS-232C communicationIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset CommandCRC Be EF BA D2 Be EF FD D3 Be EF Ntsc PAL Regulatory Notices FCC Statement WarningFor the Customers in Canada Pour les utilisateurs au Canada Page Legal Information Audio Visual Products