Dukane 28A8751 user manual Troubleshooting, OSD Messages, Message Contents

Page 29

TROUBLESHOOTING

OSD Message

The messages as described below may appear on the screen at power ON. Take the appropriate measures when such messages appears.

Table 9. OSD Messages

Message

Contents

 

 

CHANGE THE LAMP

The usage time of lamp will be reaching 2000 hr

AFTER REPLACING LAMP,

shortly.(*2)

RESET THE LAMP TIME.

It is recommended to replace the lamp soon. Prepare a

(*1)

new lamp as a replacement.

 

 

 

The usage time of lamp will be reaching 2000 hr shortly.

CHANGE THE LAMP

It is recommended to replace the lamp within * *

AFTER REPLACING LAMP,

hours.(*2)

RESET THE LAMP TIME.

It might be happened that the lamp is cut off before * * hr

THE POWER WILL TURN OFF

by any chance. Power will be switched OFF

AFTER ** hr.

automatically in * * hours. Replace the lamp as shown in

(*1)

P.17~18 “Lamp”. Always reset the lamp timer after

 

replacing the lamp.

 

 

CHANGE THE LAMP

The usage time of lamp is about to reach. Power will be

AFTER REPLACING LAMP,

switched OFF in a few minutes.(*2)

RESET THE LAMP TIME.

Switch power OFF immediately and replace the lamp as

THE POWER WILL

shown in P.17 ~18 “Lamp”. Always reset the lamp timer

TURN OFF

after replacing the lamp.

AFTER 0 hr.

 

 

 

NO INPUT IS DETECTED

No input signal found.

ON ***

Check signal input connections and signal sources.

 

 

 

The horizontal or vertical frequency of the input signal is

SYNC IS OUT OF RANGE

not within the specified range.

ON ***

Check the specifications of the equipment and the signal

 

source.

 

 

NOTE (*1) This message is cleared automatically after approximately three minutes, and appears every time power is switched ON.

(*2) The unit has a function to turn the power off which will be active when the usage time reaches 2000 hr. However the life of lamp might be much different among lamps, so that it might be happened that a lamp is cut off before the function is active.

ENGLISH

ENGLISH-19

Image 29
Contents 28A8751 Page Page Page Page Page Page Page Page Page Contents Before USE FeaturesContents of package Part Names Before USEFront / Left View Rear / Right ViewLoading the Batteries Remote ControllerFirst Loading ReplacingInstallation of the Projector and Screen InstallationAngle Adjustment Installation ReferenceCabling InstallationCabling Plug & Play Power ConnectionExample of system setup Power OFF Power onOperations StandbyBasic Operation Description OperationsBasic Operation Automatic Adjustment at RGB Input Press the Auto button Set/Clear Mute Mode Press the Mute buttonAutomatic Adjustment at Video Input Press the Auto button Normal menu Single menuSetup Menu Setup MenuSelect Image Aspect Ratio Select Position of ImageInput Menu Input MenuSelect Color Temperature Setup Initial Screen Display Select Turn on withImage Menu Image Menu DescriptionOptions Menu Description Options MenuSelect Menu Background Color Select with Select Menu Display Language Select withNo Signal Menu No Signal MenuSetup Initial Screen Display Select the Turn on with Select Blank Screen Color Select the color withLamp MaintenanceLamp Lamp LifeReplacing the Lamp MaintenanceResetting the Lamp Timer Other Maintenance Air Filter MaintenanceMaintenance Inside the Equipment Cleaning the LensMessage Contents TroubleshootingOSD Message OSD MessagesIndicators Message TroubleshootingIndicators Message IndicatorSymptom Possible cause Remedy SymptomSymptom Specifications SpecificationsWarranty and AFTER-SERVICE Page Signal Connector Pin Assignment Dimension DiagramSub 15-pin Shrink Connector RGB Mini Din 4-pin Connector S-VIDEOTechnical Example of computer signalMac 13mode Initial set signalsConnection to the Mouse Control Command data Communications settingRS-232C communication ProtocolChanging the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCRC Be EF BA D2 Be EF FD D3 Be EF Ntsc PAL For the Customers in Canada Pour les utilisateurs au Canada Regulatory NoticesFCC Statement Warning Page Legal Information Audio Visual Products