Delta Electronics LCP-2125 specifications Open

Page 5

Notes:

1)TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.

2)TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7 – 10 K Ω resistor. Its states are:

Low (0 – 0.8V):

Transmitter on

(>0.8, < 2.0V):

Undefined

High (2.0 – 3.465V):

Transmitter Disabled

Open:

Transmitter Disabled

3)Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10KΩresistor on the host board. The pull-up voltage shall be VccT or VccR (see Section IV for further details). Mod-Def 0 is grounded by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire serial interface for serial ID Mod-Def 2 is the data line of two wire serial interface for serial ID

4)LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.

5)VeeR and VeeT may be internally connected within the SFP module.

6)RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 2000 mV differential (185 – 1000 mV single ended) when properly terminated.

7)VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP connector pin. Maximum supply current is 300mA. Recommended host board power supply filtering is shown below. Inductors with DC resistance of less than 1=should be used in order to maintain the required voltage at the SFP input pin with 3.3V supply voltage. When the recommended supply-filtering network is used, hot plugging of the SFP transceiver module will result in an inrush current of no more than 30mA greater than the steady state value. VccR and VccT may be internally connected within the SFP transceiver module.

8)TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200 mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 – 600 mV single-ended) be used for best EMI performance.

5

Nov., 2006

 

Rev. 1D

DELTA ELECTRONICS, INC.

www.deltaww.com

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Description Duplex LC Connector interfaceApplications PerformanceRecommended Operating Conditions Electrical CharacteristicsAbsolute Maximum Ratings Mask of the eye diagram for the optical transmit signal Optical CharacteristicsLOS Open PLD / PAL Package Outline Drawing SFP timing parameters for SFP management Parameter Symbol Min Max UnitEnhanced Digital Diagnostic Interface Eeprom Serial ID Memory Contents 2-Wire Address A0h Unit Bytes Digital Diagnostic Monitoring InterfaceAddress Name State/ Control Bits Optional Set of Alarm and WarningEMC Cispr Regulatory ComplianceFunction Ordering information for SFP modules

LCP-2125 specifications

Delta Electronics is a global leader in power and thermal management solutions, and one of their renowned products is the LCP-2125, a cutting-edge liquid cooling pump designed for enhancing thermal management in various applications. The LCP-2125 is specifically engineered to cater to the demands of high-performance computing environments, data centers, and industrial processes that require efficient cooling solutions.

One of the standout features of the LCP-2125 is its high efficiency. Designed to minimize energy consumption while maximizing cooling performance, this pump employs advanced motor technology, reducing operational costs significantly. This is particularly beneficial in data centers, where cooling can account for a substantial portion of energy expenditure.

The LCP-2125 operates with a variable speed control mechanism, allowing for precise management of cooling power based on the specific temperature requirements of the system. This adaptability not only enhances energy efficiency but also prolongs the lifespan of equipment by ensuring they operate within optimal thermal conditions.

Another key characteristic of the LCP-2125 is its robust design, which is built to withstand harsh operational environments. The pump features corrosion-resistant materials and a durable casing that further protects against wear and tear, ensuring reliable performance over extended periods.

Delta Electronics integrates advanced monitoring and control technologies into the LCP-2125 as well. This includes real-time data tracking of flow rate, temperature, and pressure, allowing for proactive maintenance and quick identification of any potential issues. This level of monitoring is crucial in mission-critical settings where unplanned downtime can lead to significant repercussions.

Moreover, the LCP-2125 is designed for easy installation and maintenance, making it a convenient choice for facilities managers. Its compact size facilitates integration into various systems without occupying excessive space, which is an advantage in densely packed environments.

In conclusion, the Delta Electronics LCP-2125 liquid cooling pump stands out as a reliable solution that addresses the thermal management challenges of modern applications. With its energy-efficient design, robust construction, and advanced monitoring capabilities, it provides a perfect balance between performance, durability, and ease of use, making it an invaluable asset for industries reliant on high-performance computing and effective cooling systems.
Top Page Image Contents