Delta Electronics LCP-155A4HSRx manual Open

Page 5

Notes:

1)TX Fault is internally connected to TX ground.

2)TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7 – 10 K Ω resistor. Its states are:

Low (0 – 0.8V):

Transmitter on

(>0.8, < 2.0V):

Undefined

High (2.0 – 3.465V):

Transmitter Disabled

Open:

Transmitter Disabled

3)Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7K – 10KΩresistor on the host board. The pull-up voltage shall be VccT or VccR (see Section IV for further details). Mod-Def 0 is grounded by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire serial interface for serial ID Mod-Def 2 is the data line of two wire serial interface for serial ID

4)LOS (Loss of Signal) is an open collector/drain output, which should be pulled up with a 4.7K – 10KΩ resistor. Pull up voltage between 2.0V and VccT, R+0.3V. When high, this output indicates the received optical power is below the worst-case receiver sensitivity (as defined by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8V.

5)VeeR and VeeT may be internally connected within the SFP module.

6)RD-/+: These are the differential receiver outputs. They are AC coupled 100Ω differential lines which should be terminated with 100Ω (differential) at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on these lines will be between 370 and 2000 mV differential (185 – 1000 mV single ended) when properly terminated.

7)VccR and VccT are the receiver and transmitter power supplies. They are defined as 3.3V ±5% at the SFP connector pin. Maximum supply current is 300 mA. Recommended host board power supply filtering is shown below. Inductors with DC resistance of less than 1 Ω should be used in order to maintain the required voltage at the SFP input pin with 3.3V supply voltage.

8)TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100Ω differential termination inside the module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept differential swings of 500 – 2400 mV (250 – 1200 mV single-ended), though it is recommended that values between 500 and 1200 mV differential (250 – 600 mV single-ended) be used for best EMI performance.

5

Sep., 2006

 

Rev. 0B

DELTA ELECTRONICS, INC.

www.deltaww.com

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Sonet OC-3/SDH STM-1 Description ApplicationsPerformance Recommended Operating Conditions Electrical CharacteristicsAbsolute Maximum Ratings Mask of the eye diagram for the optical transmit signal Optical CharacteristicsDCD RINMOD-DEF2 Open PLD / PAL Recommend Circuit SchematicPackage Outline Drawing for Metal Housing with Bail de-latch SFP timing parameters for SFP management TxdisableTxfault SFP timing parameters Address Ordering information for SFP modules Regulatory ComplianceRelated SFP products EMI

LCP-155A4HSRx specifications

Delta Electronics, a global leader in power and thermal management solutions, has introduced the LCP-155A4HSRx, a highly efficient and versatile indoor LED display solution. Designed to cater to a variety of applications, including advertising, event displays, and broadcasting, the LCP-155A4HSRx is engineered to deliver exceptional performance, reliability, and visual appeal.

One of the standout features of the LCP-155A4HSRx is its advanced LED technology, which ensures brilliant image quality with stunning colors and high contrast ratios. This display utilizes high-resolution panels that can support a pixel pitch of 1.5mm, resulting in a sharp and vibrant visual experience, ideal for both close-up viewing and large audience engagements.

The LCP-155A4HSRx is designed with modularity in mind, allowing for easy installation and maintenance. The lightweight and slim design of the panels allows for flexible configurations, making it easy to create customized display sizes and shapes to suit any venue. Moreover, the front and rear access options enable quick servicing, minimizing downtime and ensuring that the display system remains operational with minimal disruption.

In terms of connectivity, the LCP-155A4HSRx is equipped with multiple input options, allowing it to integrate seamlessly with various video sources. This device supports high-definition content and provides flexibility in connecting to different signal formats, enhancing its usability across different applications.

The display is also designed for long-term performance with energy-efficient operation. Delta Electronics leverages cutting-edge thermal management technologies to ensure optimal thermal dissipation, resulting in reduced operating temperatures and increased longevity of the components. This translates into lower energy costs and a minimized environmental footprint.

Another key feature of the LCP-155A4HSRx is its robust build quality. Designed to withstand the rigors of indoor use, the display is IP40 rated, making it resistant to dust and suitable for various installations, from shopping malls to corporate settings.

In summary, Delta Electronics' LCP-155A4HSRx is a state-of-the-art indoor LED display solution that combines advanced technologies with exceptional features tailored for professional environments. Its modular design, high-resolution performance, energy efficiency, and durability make it an ideal choice for businesses looking to invest in a reliable visual communication tool.
Top Page Image Contents