Compaq EK-ASIP2-OG. D01 manual Installing Suitable Field Wiring, Field Wiring Recommendations

Page 58

Field Wiring the -48 Vdc Power Inverter

C.1.1 Installing Suitable Field Wiring

The following subsections describe how to install suitable field wiring.

C.1.1.1 Field Wiring Recommendations

Table C–1 lists the field wiring recommendations for each side of the -48 Vdc power controller. The -48 Vdc power controller has dual power feeds.

Table C–1: Field Wir ing Recommendations for Each Power Feed

Input Power Requirement

-48 Vdc Power Controller

Input voltage

-48 Vdc

Input current

50 A max

Inrush peak

6 A max soft start limited

 

 

Recommended wire: Wire should be U/L recognized and CSA certified for 105°C (221°F), with insulation rated for 600 Vac. Each of the 3-wire conductors should be a minimum of 6 AWG stranded.

____________________________WARNING_________________________

High energy hazard. Proper precautions required.

______________________________________________________________

___________________________ VORSICHT ________________________

Hochspannungsgefahr. Geeignete Vorsichtsmaßnahmen sind notwendig.

______________________________________________________________

C.1.1.2 Installing the Wiring

1.Strip the wire insulation to approximately 1.27 cm (.50 in.).

2.Insert the wire into the terminal block as follows:

a.Observe the wire color/polarity

–Black: -48 Vdc

–White: +48 Vdc

–Green/yellow: Ground

b.Torque the #10-32 compression screws to 40 to 45 inch-pounds.

______________________________ Note ___________________________

Refer to the DIGITAL 2T-48VDC-xx -48Vdc-to-120Vac Power Inverter Owner’s

Guide for information on powering up and testing the -48 Vdc inverter.

______________________________________________________________

C–2AlphaServer Intelligent Peripheral Platform Hardware Owner's Guide

Page 57 Page 59
Image 58
Page 57 Page 59
Contents May Compaq Computer Corporation Houston, Texas May Acoustics Page Table of Contents AlphaServer IP Platform Specifications Reconfiguring the AlphaServer IP PlatformSystem Troubleshooting Basic OperationAlphaServer IP Platform Duplex System Diagrams Alarm Input WiringField Wiring the -48 Vdc Power Inverter AlphaServer IP Platform Simplex System DiagramsViii Intended Audience PrefaceAbout This Guide Structure of This DocumentRelated Documentation ConventionsConvention Meaning Introduction Product OverviewIP Platform Overview IP Simplex System IP Duplex SystemFactory Installed Software User Interfaces System FeaturesAlarm Subsystem MaintainabilityCompaq Computer Corporation and Industry Standards Safety and Electromagnetic CompatibilityUpgrading Telecommunications InterfacesSystem Security AlphaServer 1000A SystemRequired and Optional Hardware OverviewAlphaServer 1000A Required Hardware Part Number Description Simplex DuplexModular Storage Shelf Optional Hardware Modular Storage Shelf Subsystem BA35x-SxISA Bus Expansion Chassis Modular Storage Shelf BA35x-Sx Optional HardwareISA Bus Expansion Chassis Required and Optional Hardware Part Number Description Simplex DuplexIP Power Controller Options IP Power Controller SubsystemAlarm Indicator Panel Alarm Indicator Panel OptionsExternal Hardware Options External Hardware OptionsPage Installing the AlphaServer IP Platform Hardware Factory Installed HardwareSite Preparation Preinstallation ConsiderationsAchtung Hardware Installation VorsichtInstalling the IP Platform Connecting the Network HardwareT-1 to D/240SC-T1 Pin Designations Connecting Dialogic D/240SC-T1 and DTI/211 T-1 ModulesSignal Pins T1 to DTI/211 Pin DesignationsSignal Jack/Pin Connecting Dialogic DTI/212 E-1 Modules 75-OhmConnecting Dialogic DTI/212 E-1 Modules 120-Ohm E-1 to DTI/212 75-Ohm Pin DesignationsConnecting Dialogic LSI/120 Loop-Start Module LSI/120 Loop-Start 25-Pin DesignationsUser Alarms IP Power ControllerLSI/120 Loop-Start 50-Pin Designations Locking Your System Page Step III AlphaServer 1000A System Turning on the AlphaServer IP PlatformStep I Power Controller Circuit Breakers Basic OperationVisual Indicators Basic Operation of the IP Platform Subsystem ComponentsAlarm Indicator Panel Front and Rear View Audible Indicator Replacing Batteries in the Alarm Indicator PanelDry Contacts Dry Contact Relay Functional Specification Power Condition Relay State Critical Major MinorModular Storage Shelf BA35x-Sx Subsystem Voltage Amps Reconfiguring the AlphaServer IP Platform SRM Console Configuration Commands AlphaServer 1000A System ConfigurationsCommand Description ISA Bus Expansion Chassis Configuration Removing and Replacing the Alarm Sensor ModuleModular Storage Shelf BA35x-Sx Subsystem Configuration Removing and Replacing the AT Bus Expansion KitAlarm Indicator Panel Configuration Removing and Replacing the Alarm Indicator ModulePage System Troubleshooting AlphaServer 1000A Subsystem Alarm Indicator PanelISA Bus Expansion Chassis AlphaServer IP Power ControllersModular Storage Shelf BA35x-Sx Subsystem Page Electrical Specifications AlphaServer IP Platform SpecificationsPhysical Dimensions Table A-1 Physical DimensionsOperating/Storage Conditions System Environmental SpecificationsTable A-3 Environmental Specifications Nonoperating ConditionsInput Specifications Dry Contact SpecificationsTable A-4 Dry Contact Specifications Output SpecificationsCentral Office Compatibility Alarm Input Wiring Alarm Input Wiring DiagramTable B-1 Alarm Control M odule 8-Pin MJ Connector Pinout Wiring User Alarm InputsPin No Signal Field Wiring the -48 Vdc Power Inverter Field Wiring the -48 Vdc Power ControllersTable C-1 Field Wir ing Recommendations for Each Power Feed Installing Suitable Field WiringField Wiring Recommendations Installing the WiringAlphaServer IP Platform Duplex System Diagrams AlphaServer IP Platform Duplex AC System Figure D-1 IP Platform D uplex AC System Front and Side ViewFigure D-2 IP Platform D uplex AC System Rear View AlphaServer IP Platform Duplex DC System Figure D-3 IP Platform D uplex DC System Front and Side ViewFigure D-4 IP Platform D uplex DC System Rear View Page AlphaServer IP Platform Simplex System Diagrams AlphaServer IP Platform Simplex AC System Figure E-1 IP Platform Simplex AC System Front and Side ViewFigure E-2 IP Platform Simplex AC System Rear View AlphaServer IP Platform Simplex DC System Figure E-3 IP Platform Simplex DC System Front and Side ViewFigure E-4 IP Platform Simplex DC System Rear View Page Glossary Diagnostic program Command line interfaceConsole mode BusEnvironment variables Eisa Configuration Utility ECUEisa bus EthernetLight-emitting diode LED MAC media access control addressMaintenance Operations Protocol MOP session Mass storage deviceRepeater RedundantReliability ServerSystem disk ThinWireStorageWorks TelnetIndex Index

EK-ASIP2-OG. D01 specifications

The Compaq EK-ASIP2-OG. D01 is a significant product in the landscape of enterprise computing, featuring a range of capabilities that cater directly to the needs of businesses seeking high-performance solutions. This hardware is designed for a range of applications, offering a solid balance between efficiency and power, making it suitable for varying workloads.

One of the key features of the EK-ASIP2-OG. D01 is its robust processing architecture. It is equipped with advanced microprocessor technology that ensures high-speed data processing and multitasking capabilities. This feature is particularly valuable in environments that require the simultaneous execution of multiple applications, thereby enhancing productivity and operational efficiency.

In addition to processing power, the EK-ASIP2-OG. D01 integrates significant memory capacity. This ensures that large applications can run smoothly without performance bottlenecks. The system supports scalable memory configurations, allowing users to optimize their setup according to their specific needs. This flexibility is essential for organizations that anticipate growth or require variable resource allocation.

Networking capabilities are another standout aspect of the EK-ASIP2-OG. D01. It comes with advanced network interfaces that promote seamless connectivity and high-speed data transfer. This is crucial for enterprise environments where data needs to be shared across various departments or locations in real time. The integration of leading networking technologies ensures reliable communication and collaboration, which are vital for modern business operations.

Furthermore, the EK-ASIP2-OG. D01 is designed with advanced security features, addressing the growing concerns around data protection. These features include encryption capabilities and secure access controls, ensuring that sensitive information remains safeguarded against potential threats. This focus on security makes it an ideal choice for businesses that prioritize safeguarding their data.

In terms of energy efficiency, the EK-ASIP2-OG. D01 employs power management technologies that reduce energy consumption without compromising performance. This not only contributes to cost savings for organizations but also aligns with sustainability goals, a factor increasingly important to businesses globally.

In conclusion, the Compaq EK-ASIP2-OG. D01 is a powerful and versatile server solution, equipped with cutting-edge technologies, robust security features, and sustainable energy practices. It is designed to meet the demands of modern enterprises, making it a reliable choice for businesses looking to enhance their computing capabilities and overall operational efficiency.
Top Page Image Contents