Christie Digital Systems 38-VIV303-01 To change the code of Projector, Power management, On start

Page 39

SETTING

Power management

This projector is equipped with a power management function. When the input signal is interrupted and any button is not pressed for 30 seconds or more, the power management function operates in order to reduce power consumption and conserve lamp operating time. The factory default settings for power management are "Ready" and "5 Min".

OPERATION

1)If the input signal is interrupted and any button is not pressed for 30 seconds or more, the message "No signal" and the timer display appears on the screen. Then the count-down starts for the time being set.

If "Ready" is selected

2)When the set time is elapsed, the lamp will be switched off and lamp cooling starts. The READY indicator will be switched off while the lamp cooling is in progress, and the projector cannot be operated during this time.

3)When the lamp cooling is completed, the READY indicator starts flashing to notify the operator that power management mode is active. In this condition, the lamp will turn on and images will be projected if a signal starts being input or the projector is operated.

If "Shut down" is selected

2)When the set time is elapsed, the lamp will be switched off and lamp cooling starts. The READY indicator will be switched off while the lamp cooling is in progress, and the projector cannot be operated during this time.

3)When the lamp cooling is completed, the power switches off.

If "Off" is selected

The power management function is canceled.

When a SELECT button is pressed, the adjustment screen is displayed.

Use the POINT LEFT/RIGHT button(s) to select the power management function mode ("Off", "Ready" or "Shut down").

Use the POINT DOWN button to move the pointer to the time setting, and then use the POINT LEFT/RIGHT button(s) to set the time (1 minute to 30 minutes).

On start

Time left until Lamp off.

When this function is “On,” projector is automatically turned on just by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to section “TURNING OFF PROJECTOR” on P20). If projector is turned off in wrong steps, On Start function does not operate properly.

Remote control

This projector has eight different remote control codes; the factory- set normal code (Code 1) and the other seven codes (Code 2 to Code 8). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together.

For example operating projector in “Code 7,” both projector and Remote Control Unit must be switched to “Code 7.”

To change the code of Projector;

To change the Remote control code of the projector used in ON-

SCREEN MENU is selectable from Code 1 to Code 8.

To change the code of the Remote Control Unit;

To change the remote control code of the Remote Control Unit, set the DIP switches 1-3 inside the battery compartment box of the Remote Control Unit. (Refer to P15.)

When pressing SELECT button at Remote control, Remote control code Menu appears.

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Model To the Owner Voor de klanten in Nederland Safety InstructionsCamden Drive Cypress, CA 90630 USA CompliancesTable of Contents Compact Design Digital Zoom for Computer Features and DesignPreparation Name of Each Part of ProjectorHOT AIR Exhausted SETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Preparation Lens Installation Positioning ProjectorRoom Light Installing Projector in Proper Position Preparation Adjustable FeetPreparation Moving Projector Refer to P13 Connecting ProjectorTerminals of Projector Connect computer output Digital DVI-D type to this terminalConnecting to Computer TerminalsA Projector Connecting to Video Equipment Laser Pointer Function Operation of Remote ControlInside the Battery Compartment BOX Before OperationCompartment Remove batteryCompartment lid Slide batteries intoTOP Controls and Indicators HOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Used to select Press Menu Button while connecting to PC input sourceUsed to adjust picture image Before Operation Menu BARTurning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorCorrected by Keystone adjustment Adjusting ScreenKeystone Adjustment Focus adjustment may not function properly if the image isSound Adjustment Rgbav Hdcp Computer InputSelecting Input Source Selecting Computer SystemAutomatic MULTI-SCAN System AutoPC System Menu Auto PC Adj PC AdjustmentAuto PC Adjustment PC Adjust MenuComputer Input Manual PC Adjustment Display area Display area HFull screen Image Select Menu Picture Image SelectImage Level Select Direct Image Level Select MenuScreen Menu Picture Screen AdjustmentSelect Video When video input signal is connected to Video jackVideo Input VideoAV System Menu Component Video Selecting Video SystemAuto AV System Menu Video or S-VIDEOCinema Picture level adjusted for picture with fine toneProvides image at a wide screen ratio of 16 Provides image at a normal video aspect ratio of 4Picture Image Adjustments Image Adjust MenuPicture Image List Mode White balance Blue Color tempWhite balance Red White balance GreenSetting Setting MenuSetting Menu Menu position AnamorphicBlue back DisplayTo change the code of Projector To change the code of the Remote Control UnitPower management Remote controlFactory default Wireless Mouse modeProjector mode Lamp counter resetAppendix Operating Wireless MouseInstallation Operating Wireless MouseMaintenance IndicatorIndicatorStation Pull up and remove Appendix AIR Filter Care and CleaningCleaning Projection Lens RecommendationLamp Replace Lamp ReplacementPointer to Yes and then press Select button Message Lamp replace counter reset? is displayed. MoveReset Lamp Replace Counter Appendix Lamp Replace CounterTroubleshooting Service Appendix Indicators and Projector Condition Resolution Appendix Compatible Computer SpecificationsPC source Menu TreeSystem Setting Sound Technical Specifications Computer INPUT-1 and Monitor OUT Terminals Analog Appendix Configurations of TerminalsControl Port Connector USB Connector Series BLens Replacement To the sales and service engineerAppendix Optional Parts Appendix Part No -A 610 309 0559 1AA6P1P4203-- MR3KL

38-VIV303-01 specifications

Christie Digital Systems 38-VIV303-01 is an innovative display solution designed for various professional environments, including corporate settings, control rooms, and entertainment venues. This model stands out due to its high-definition image quality and advanced technology, making it an excellent choice for users seeking superior visual performance.

One of the prominent features of the 38-VIV303-01 is its impressive resolution. With a native 1920x1080 resolution, it delivers sharp and detailed images, ensuring that content is displayed with exceptional clarity. This high resolution is vital for applications such as video conferencing, where clear visuals are essential for effective communication.

In terms of size, the 38-VIV303-01 boasts a generous 38-inch diagonal screen, making it suitable for both small and large venues. The display offers an ultra-thin bezel design, allowing for seamless multi-display configurations. This feature is particularly advantageous for users who require multiple screens for a panoramic viewing experience or for creating video walls to engage audiences effectively.

The display employs advanced LED backlighting technology, which enhances brightness and contrast, resulting in vibrant and lifelike colors. Additionally, the 38-VIV303-01 supports a wide color gamut, ensuring that colors are reproduced accurately and vividly. This is particularly important for applications in media production or graphic design, where color fidelity is paramount.

Christie Digital Systems has also incorporated intelligent energy-saving features into the 38-VIV303-01. This helps reduce power consumption without compromising performance, making the display an eco-friendly option. Users can benefit from extended lifespan and reduced operating costs, a crucial factor for businesses that rely on these systems for continuous operation.

Furthermore, the 38-VIV303-01 is designed with connectivity in mind. It comes equipped with multiple input ports, including HDMI and DisplayPort, enabling seamless integration with various devices such as laptops, desktops, and media players. This versatility ensures that users can easily connect and switch between different sources of content.

Overall, Christie Digital Systems 38-VIV303-01 is a robust and feature-rich display solution that caters to the needs of modern professional environments. With its superior image quality, advanced technologies, and enhanced connectivity, it provides a reliable platform for presenting information and engaging audiences effectively. Whether in control rooms, conference halls, or entertainment settings, the 38-VIV303-01 stands out as a powerful tool for enhancing visual communication.
Top Page Image Contents