Christie Digital Systems XENON CONSOLE manual L O W E R

Page 33

7 : O p e r a t i n g t h e S L C X e n o n C o n s o l e

These items should be cleaned approximately every six months under normal environmental conditions. Equipment in very dusty or otherwise contaminated areas may require more frequent maintenance.

7 . 3 . 1 . B L O W E R

The blower impeller and motor should be cleaned to prevent build-up of contaminant on both the blower impeller surfaces and on the blower motor. Proper operation of the lamp is dependent on providing adequate cooling air flow. A dirty blower may not provide proper air flow, causing the lamp and lamphouse to operate at temperatures that are higher than intended.

1.Clean loose dirt from blower impeller with vacuum cleaner.

2.Use brush with hot water and suitable detergent to remove dirt that cannot be vacuumed off.

When cleaning the impeller, be careful not to bend the blades or to loosen the balancing weights.

3.Every six months, lubricate blower motor by applying three to four drops of light machine oil to oil holes in motor housing.

7 . 3 . 2 . I G N I T E R

Periodically clean the high voltage terminal and insulator to prevent accumulation of dust or dirt.

7 . 3 . 3 . A I R F L O W I N T E R L O C K S

Periodically check and, if necessary, clean the air flow interlock vanes to remove accumulated dirt.

7.4. ALIGNING LAMPHOUSE WITHOUT ALIGNMENT TOOLS

1.Inspect reflector and lens and clean if necessary.

2.Inspect lamp for dirt or fingerprints. Clean if required.

3.Center lamp adjustments in rear of lamphouse to midpoint of their range.

4.Install lamp in lamphouse.

5.Use ruler to verify that positive end of lamp is centered in reflector from top to bottom and side to side. If not centered, adjust to center position by adjusting the front lamp support.

6.For best results: With ruler, verify that positive end of lamp is centered left to right in reflector within 1/16 in. If not centered, adjust front lamp support to center lamp.

CHRISTIE DIGITAL SYSTEMS

7-3

August 7, 2003

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Digital Systems Christie Digital Systems Table of Contents Warranty List of Figures and Tables Figure A-7 Power Supply Table A-7Page Introduction A R N I N G A U T I O N O T E Protective Clothing Safety Kit Contents Safety PrecautionsV E R L O O K D I R E C T L Y a T T H E L a M P Avoid Fire Hazards Page General Description Page Installation Procedures SLC Xenon Lamp Console Front View SLC Xenon Lamp Console Rear View O O R P a N E L S I R I N G H O O K U P AC Wiring Hook-Ups Alignment and Checkout Procedures Plenum, Top View L i g n m e n t a n d C h e c k o u t P r o c e d u r e s Page Operating the SLC SLC 20 SLC 40, 45 P e r a t i n g t h e S L C X e n o n C o n s o l e Optical Alignment of Xenon Lamp Tilt Adjustment Christie Digital Systems Maintenance and Adjustments Always remove the lamp before cleaning the reflector L O W E R 24 VDC 115 VAC Airflow Troubleshooting for Power Supply Does Not Start TroubleshootingTroubleshooting for Power Supply Output Low or Not Steady Troubleshooting for Lamp Does Not IgniteWarranty Christie Digital Systems Appendix a Figure A-1 Autofocus Assembly Description Part Number Table A-1 Parts List for Autofocus AssemblyFigure A-2 SLC Xenon Lamp Console Front View Blower SLC 40,45 Table A-2 Parts List for SLC Xenon Lamp Console Front ViewFigure A-3 SLC Xenon Lamp Console Rear View Capacitor SLC 40, 45 Table A-3 Parts List for SLC Xenon Lamp Console Rear ViewSLC 20 SLC 40, 45 Table A-4 Parts List for Control Panel Figure A-5 Manual Lamp Adjustment Assembly Table A-5 Parts List for Manual Lamp Adjustment Assembly Figure A-6 Plenum , All Models Top View CXL-16S Table A- 6 Parts List for Plenum, All Models Top ViewFigure A-7 Power Supply Capacitor C1 SLC 40, 45 Table A-7 Power SupplyPage Appendix B Figure B-1 Schematic Diagram for IGA-10 Igniter P/N Figure B-2 Schematic Diagram for IGA-15M Igniter P/N Page Page Figure B-3 SLC 20-CC20, SLC 30-CC25 Console Side View Front View

XENON CONSOLE specifications

Christie Digital Systems has established itself as a leader in visual display solutions, and the XENON CONSOLE is a formidable addition to their product line. This high-performance console is designed to meet the rigorous demands of modern post-production environments, enhancing both productivity and creative output.

One of the main features of the XENON CONSOLE is its exceptional capability for real-time color grading and detailed image manipulation. This console boasts advanced technology that provides unparalleled accuracy and consistency in color reproduction, critical for filmmakers and video editors who rely on precise visual representation. The high dynamic range and a wide color gamut ensure that the content appears vibrant and true to life.

The ergonomically designed interface of the XENON CONSOLE enhances user experience, allowing for seamless operation in high-pressure settings. It features customizable control layouts that can be tailored to meet the unique preferences and requirements of individual users. This flexibility enables operators to streamline their workflow and focus more on creativity rather than technical limitations.

The console is equipped with state-of-the-art processing power, featuring powerful GPUs and processors that enable real-time playback of high-resolution video content. This capability is especially important for projects that involve 4K and even 8K video resolutions, allowing for smooth transitions and instant feedback during the editing process.

Another highlight of the XENON CONSOLE is its integration with various industry-standard software applications and tools. Whether users are working in color grading software like DaVinci Resolve or visual effects programs such as Adobe After Effects, the console offers compatibility that ensures a cohesive working environment without technological barriers.

Connectivity is another strong point for the XENON CONSOLE. It provides a range of input and output options, accommodating various formats and devices. This versatility allows it to fit seamlessly into existing studio setups, connecting with cameras, external drives, and other critical tools.

The build quality of the XENON CONSOLE reflects Christie’s commitment to durability and reliability. Designed for the rigors of continuous professional use, the console features robust materials and components, promising longevity and consistent performance over time.

In summary, the Christie Digital Systems XENON CONSOLE stands out for its advanced technological capabilities, user-friendly design, extensive software compatibility, and robust build quality. As a reliable tool in the professional media landscape, it empowers creators to realize their vision with precision and ease.
Top Page Image Contents