Christie Digital Systems XENON CONSOLE manual Tilt Adjustment

Page 29

7 : O p e r a t i n g t h e S L C X e n o n C o n s o l e

6.4. TILT ADJUSTMENT

The SLC Console is optionally equipped with a jackscrew for easy tilt adjustment. It is located in the bottom rear of the console, and is accessible from either side. (See Item 16 in Figure 4-2.)

1.Loosen all four (4) hold-down bolts. (See Item 7 in Figure 4-1.)

2.Turn jackscrew using 3/4-inch wrench or ratchet. Turn jackscrew clockwise to tilt console downward. Turn jackscrew counterclockwise to tilt console upward.

3.After reaching correct tilt angle, securely tighten all four hold-down bolts.

6.5. REPLACING THE LAMP

In accordance with safety precautions, always be certain that the lamp has cooled for at least 10 minutes before replacing it.

Authorized protective clothing must be worn when replacing lamp.

WARNING

6 . 5 . 1 . R E M O V I N G T H E L A M P

Christie recommends that lamps be replaced before running time exceeds 120% of warranted lifetime. Check running time using elapsed time indicator on control panel (Item 3 in Figure 6-1).

1.Loosen set screws on positive and negative lamp connectors.

2.Unscrew lamp and remove from reflector. Immediately put protective cover on lamp.

3.Record hours that lamp has been used.

Record the elapsed time reading for the old lamp when installing a new lamp.

6 . 5 . 2 . I N S T A L L I N G A N E W L A M P

Install the new Xenon lamp according to the directions in Section 5.2.

6 . 5 . 3 . D E F E C T I V E L A M P S

Defective lamps under warranty are to be returned to the dealer who provided the lamp in their protective cover and proper packing. They must be returned to Christie. The Warranty Claim Forms supplied with the lamp must be filled out completely. All portions of the failed lamp including electrodes must accompany the lamp to aid Christie in evaluating the defect.

CHRISTIE DIGITAL SYSTEMS

6-5

August 7, 2003

 

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Digital Systems Christie Digital Systems Table of Contents Warranty List of Figures and Tables Figure A-7 Power Supply Table A-7Page Introduction A R N I N G A U T I O N O T E Protective Clothing Safety Kit Contents Safety PrecautionsV E R L O O K D I R E C T L Y a T T H E L a M P Avoid Fire Hazards Page General Description Page Installation Procedures SLC Xenon Lamp Console Front View SLC Xenon Lamp Console Rear View O O R P a N E L S I R I N G H O O K U P AC Wiring Hook-Ups Alignment and Checkout Procedures Plenum, Top View L i g n m e n t a n d C h e c k o u t P r o c e d u r e s Page Operating the SLC SLC 20 SLC 40, 45 P e r a t i n g t h e S L C X e n o n C o n s o l e Optical Alignment of Xenon Lamp Tilt Adjustment Christie Digital Systems Maintenance and Adjustments Always remove the lamp before cleaning the reflector L O W E R 24 VDC 115 VAC Airflow Troubleshooting for Power Supply Does Not Start TroubleshootingTroubleshooting for Power Supply Output Low or Not Steady Troubleshooting for Lamp Does Not IgniteWarranty Christie Digital Systems Appendix a Figure A-1 Autofocus Assembly Description Part Number Table A-1 Parts List for Autofocus AssemblyFigure A-2 SLC Xenon Lamp Console Front View Blower SLC 40,45 Table A-2 Parts List for SLC Xenon Lamp Console Front ViewFigure A-3 SLC Xenon Lamp Console Rear View Capacitor SLC 40, 45 Table A-3 Parts List for SLC Xenon Lamp Console Rear ViewSLC 20 SLC 40, 45 Table A-4 Parts List for Control Panel Figure A-5 Manual Lamp Adjustment Assembly Table A-5 Parts List for Manual Lamp Adjustment Assembly Figure A-6 Plenum , All Models Top View CXL-16S Table A- 6 Parts List for Plenum, All Models Top ViewFigure A-7 Power Supply Capacitor C1 SLC 40, 45 Table A-7 Power SupplyPage Appendix B Figure B-1 Schematic Diagram for IGA-10 Igniter P/N Figure B-2 Schematic Diagram for IGA-15M Igniter P/N Page Page Figure B-3 SLC 20-CC20, SLC 30-CC25 Console Side View Front View
Top Page Image Contents