Christie Digital Systems Complete Guide to Christie Projector Troubleshooting
Page 40

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check matters below once again.

1.Make sure you have connected the projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 11 ~ 13.

2.Check cable connection. Verify that all computer, video and power cord are properly connected.

3.Verify that all power is switched on.

4.If the projector still does not produce an image, re-start your computer.

5.If an image still does not appear, unplug the projector from your computer and check your computer monitor's display. The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, be sure to turn the computer and monitor off before you power up the projector. Power equipment back on in order of : Projector and computer.)

6.If problem still exists, check following chart.

Problem:

Try these Solutions

No power.

● Plug the projector into your AC outlet.

 

● Make sure READY Indicator lights.

 

● Wait 90 seconds after the projector is turned OFF before turning the projector back on.

 

NOTE : After pressing Power ON-OFF button to OFF, make sure the projector works as

 

follows:

 

1. LAMP indicator lights bright and READY indicator turns off.

 

2. After 90 seconds, READY indicator lights green again and the projector may be

 

turned on by pressing Power ON-OFF button.

 

● Check WARNING TEMP. indicator. If indicator flashes red, the projector can not be

 

turned on.

 

(See "TURNING ON/OFF PROJECTOR" section on page 19.)

 

● Check Projection Lamp. (Refer to page 39.)

 

 

Image is out of

● Adjust focus of the projector.

focus.

● Make sure the projection screen is at least 4.6’ (1.4m) from the projector.

● Check Projection Lens to see if it needs cleaning.

 

 

NOTE : Moving the projector from a cool temperature location to a warm temperature

 

location may result in moisture condensation on Projection Lens. In such an event,

 

leave the projector OFF and wait until condensation disappears.

 

 

Picture is Left/Right

● Check Ceiling / Rear feature. (See “SETTING” section on page 35.)

reversed.

 

 

 

Picture is

● Check Ceiling feature. (See “SETTING” section on page 35.)

Top/Bottom

 

reversed.

 

 

 

Some displays are

● Check Display feature.(See “SETTING” section on page 35.)

not seen during

 

Operation.

 

 

 

No image.

● Check connection between your computer or video equipment and the projector.

 

● When turning the projector on, it takes about 30 seconds to display an image.

 

● Check system that you select is corresponding with your computer or video equipment.

 

● Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).

No sound.

● Check audio cable connection from audio input source.

 

● Adjust audio source.

 

● Press VOLUME (+) button.

 

● Press MUTE button.

 

 

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Model To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact Design Digital Zoom for ComputerPreparation Name of Each Part of ProjectorConnecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Lens Shift Adjustment Preparation Lens InstallationPositioning Projector Preparation Adjustable Feet Moving ProjectorConnecting Projector USB Connector Series BTerminals of Projector Audio Input JacksConnecting to Computer Terminals ProjectorConnecting to Video Equipment Audio VideoBefore Operation Operation of Remote ControlLaser Pointer Function Volume Button Wired Remote JackZoom Button Focus ButtonTOP Control Panel and Indicators Ready IndicatorOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARSound Menu Turning on Projector Turning on / OFF ProjectorTurning OFF Projector Adjusting Screen Zoom AdjustmentFocus Adjustment Keystone AdjustmentSound Adjustment Computer Input Selecting Input SourceSelecting Computer System Input MenuPC Adjustment Auto PC AdjustmentComputer Input Automatic MULTI-SCAN System AutoComputer Input Manual PC Adjustment Computer Input Display areaDisplay area H Full screenComputer Input Compatible Computer Specifications Resolution640 x 31.469 59.940 1024 x 48.363 60.004Picture Image Adjustment Image Level Select DirectImage Level Select Menu Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Input VideoComponent Video Signal Format Selecting Video SystemVideo Input PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Video Input Image Level Adjustment To function that you want to select and then press Select Setting Menu SettingSetting Menu To change code of Remote Control Unit Wireless Mouse modeProjector mode To change code of ProjectorSETTING/APPENDIX Operating Wireless MouseInstallation Operating Wireless MouseAIR Filter Care and Cleaning MaintenanceCleaning Projection Lens Appendix Lamp Replacement Lamp Replace CounterTroubleshooting Service Technical Specifications Appendix Configurations of Terminals USB Connector Series BPart No -A 610 302 1201 1AA6P1P3600-- MA8KM

38-VIV206-01 specifications

Christie Digital Systems has long been a leader in providing innovative visual display solutions, and their 38-VIV206-01 model stands out as a prime example of their commitment to quality and performance in the display technology sector. This model is particularly popular in environments that require high-performance visuals, such as control rooms, corporate environments, and immersive installations.

The 38-VIV206-01 boasts an impressive 38-inch display, offering vivid colors and stunning clarity that enhances the viewing experience. One of its primary features is its high-definition resolution, which delivers crisp images and fine details, making it ideal for applications that require precision and attention to detail.

In terms of technology, the 38-VIV206-01 leverages advanced LED backlighting technology, which not only improves energy efficiency but also produces a wider color gamut. This feature enables users to display a more extensive range of colors, ensuring that graphics and visuals appear more lifelike. Additionally, the display supports 4K resolution, allowing users to enjoy ultra-sharp images and fluid motion.

Another key characteristic of the 38-VIV206-01 is its design versatility. It can be seamlessly integrated into various setups, whether as a standalone display or as part of a larger video wall configuration. Its slim bezels contribute to an immersive viewing experience by minimizing distractions between multiple screens.

Connectivity is also a strong point of the 38-VIV206-01, which includes multiple input options such as HDMI, DisplayPort, and VGA. This flexibility allows users to connect various devices easily, making it suitable for diverse operational needs. The display also supports daisy chaining, simplifying multi-screen setups.

The 38-VIV206-01 is engineered for reliability, featuring robust construction that ensures longevity in demanding environments. It includes built-in thermal management to mitigate overheating, which is crucial for continuous operation.

Overall, the Christie Digital Systems 38-VIV206-01 is an exceptional choice for professionals looking for a high-quality display solution. Its cutting-edge features, combined with its reliability and versatile connectivity options, make it a valuable asset for any visual display requirement. Whether for business presentations, control room monitoring, or immersive multimedia environments, this model delivers top-tier performance.
Top Page Image Contents