BenQ MP782 ST Setting the presentation timer, Presentation Timer, Selection Description

Page 36

4.Press to highlight Hue and press / to select its range. Increase in the range will include colors consisted of more proportions of its two adjacent colors.

Please refer to the illustration to the right for how the colors relate to each other.

For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta.

5.Press to highlight Saturation and adjust its values to your preference by pressing / . Every adjustment made will reflect to the image immediately.

RED Yellow GREEN

Magenta Cyan

BLUE

For example, if you select Red and set its

value at 0, only the saturation of pure red will be affected.

Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

6.Press to highlight Gain and adjust its values to your preference by pressing / . The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately.

7.Repeat steps 3 to 6 for other color adjustments.

8.Make sure you have made all of the desired adjustments.

9.Press MENU/EXIT to exit and save the settings.

Setting the presentation timer

Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

1. Press Timer Set up on the remote control or go to the SYSTEM SETUP: Basic > Presentation Timer menu and press MODE/ENTER to display the

Presentation Timer page.

2. Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute

increments and 5 to 240 minutes in 5-minute increments.

If the timer is already on, the timer will restart whenever the Timer Period is reset.

3.Press to highlight Timer Display and choose if you want the timer to show up on the screen by pressing / .

Selection

Description

Always

Displays the timer on screen throughout the presentation

time.

 

1 min/2 min/3 min

Displays the timer on screen in the last 1/2/3 minute(s).

Never

Hides the timer throughout the presentation time.

36 Operation

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Welcome MP782 ST Digital ProjectorTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideLamp cover External control panel Controls and functions ProjectorRemote control Auto Mode Operating the Laser pointerToggles projector audio between on and off Locks the keys on the projectorRemote control effective range Replacing the remote control batteriesApprox.+15 Positioning your projector Choosing a locationFront Table Front CeilingObtaining a preferred projected image size Page Projection dimensions A1 a A2 aDiagonal Height Width From screen Offset Inches 762 B1 a B2 aDistance Diagonal Height Width From screen Offset InchesConnection Connecting a computer or monitor Connecting a computerConnecting a monitor To connect the projector to a notebook or desktop computerConnecting video source devices Connecting audioConnecting a Component Video source device Connecting a DVI-D deviceTo connect the projector to a DVI-D device To connect the projector to a Component Video source deviceConnecting an S-Video/Composite Video source device To connect the projector to an S-Video/Video source deviceOperation Starting up the projectorAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Securing the projectorIf you forget the password Entering the password recall procedureChanging the password Write down the number and turn off your projectorDisabling the password function Correcting keystoneBottom of the image Operation Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant Color Selecting a color temperatureAbout color temperatures 3D Color ManagementSetting the presentation timer Presentation TimerSelection Description To cancel the timer, perform the following steps How to use the Timer On key?Using the remote control Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Hiding the imageUtilizing FAQ function Go to the System Setup Basic Panel Key LockLocking control keys To exit the OSD menu, press MENU/EXITAdjusting the sound Adjusting the sound levelTurning on the Power On/Off Ring Tone Operating in a high altitude environmentConfiguring the Lan Control Settings Personalizing the projector menu displayControlling the projector through a Lan environment If you are in a Dhcp environmentIi. To switch input signal, click on your desired signal Controlling the projector remotely through a web browserIf you are in a non-DHCP environment Iiii Iiiv Shutting down the projector Menu operation Menu systemMain menu Sub-menu Options BasicAdvanced Closed Caption On/Off Enable Caption Version Control By RJ45/RS232Projector IP Lan Control AddressDescription of each menu Picture menu Function Description Picture Mode TemperatureSave Settings ReferenceSystem Setup Basic menu Function Description Quick Auto TimerSettings Auto PowerSystem Setup Advanced menu Function Description Quick CoolingHigh AltitudeSystem Setup Advanced menu Function Description Reset AllClosed CaptionFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Loosen the screws that secure the lampRemove the lamp cover from the projector Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timerTighten the screws that secure the lamp cover Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 127.87 mm H x 252 mm DCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for DVI-D & Hdmi Hdcp input Signal Format Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directive

MP782 ST specifications

The BenQ MP782 ST is a versatile short-throw projector designed to enhance presentations and multimedia experiences in both classroom and corporate settings. This projector stands out for its high-definition display capabilities, compact design, and user-friendly features.

One of the key features of the MP782 ST is its short-throw projection technology. The projector can produce a large image from a short distance, allowing users to place it close to the wall or screen while still achieving a screen size of up to 100 inches. This makes it ideal for smaller rooms where space can be a constraint. The ability to project in tight spaces means that the audience can be closer to the image without the risk of casting shadows or obstructing the view.

In terms of image quality, the MP782 ST boasts a native resolution of 1280x800 (WXGA) and a brightness level of 3000 ANSI lumens. This combination ensures that images and presentations are clear and vibrant, even in well-lit environments. Additionally, the projector features a contrast ratio of 4000:1, allowing for deeper blacks and more vivid colors, which enhances the overall visual experience.

The MP782 ST is equipped with several advanced technologies that contribute to its impressive performance. Its SmartEco technology optimizes lamp power and extends the lifespan of the lamp up to 6000 hours, reducing maintenance costs and ensuring reliability during long presentations. Furthermore, the projector utilizes BrilliantColor technology, which enhances color accuracy and delivers more realistic images across various media types.

Connectivity is another strong suit of the BenQ MP782 ST. It features multiple input options, including HDMI, VGA, and USB, making it compatible with a variety of devices such as laptops, Blu-ray players, and document cameras. This versatility allows users to seamlessly integrate the projector into their existing technology setup.

The design of the MP782 ST also includes practical features for ease of use. It has a low fan noise level, ensuring that it operates quietly during presentations. Additionally, its lightweight construction makes it easily portable, allowing for flexibility in different settings, whether it be a classroom, conference room, or training facility.

Overall, the BenQ MP782 ST is a dynamic projector that combines short-throw technology, high brightness, and robust connectivity options to deliver a reliable and impressive presentation experience. Its thoughtful design and advanced features make it a strong choice for educators and business professionals alike, facilitating engaging and effective communication.
Top Page Image Contents