BenQ MP782 ST Personalizing the projector menu display, Configuring the Lan Control Settings

Page 41

Personalizing the projector menu display

The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance.

•Menu Display Time in the SYSTEM SETUP: Basic > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time.

•Menu Position in the SYSTEM SETUP: Basic > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position.

•Language in the SYSTEM SETUP: Basic menu sets your familiar language for the On- Screen (OSD) Menus. Use / to select your language.

•Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen.

Controlling the projector through a Lan environment

Lan Control Settings allow you to manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network.

Configuring the Lan Control Settings

If you are in a DHCP environment:

1.Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port.

2.Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

3.Press to highlight Lan Control Settings and press MODE/ENTER. The Lan Control Settings page is displayed.

4.Press to highlight Control By and press / to select RJ45.

5.Press to highlight DHCP and press / to select On.

6.Press to highlight Apply and press MODE/ENTER.

7.Re-enter the Lan Control Settings page. The Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings will be displayed. Note down the IP address displayed in the Projector IP Address row.

If the Projector IP Address still does not appear, contact your ITS administrator.

Operation 41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents MP782 ST Digital Projector WelcomeTable of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Lamp cover External control panel Projector exterior viewFront/upper side Rear/lower side Projector Controls and functionsRemote control Operating the Laser pointer Auto ModeToggles projector audio between on and off Locks the keys on the projectorApprox.+15 Remote control effective rangeReplacing the remote control batteries Choosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Page Diagonal Height Width From screen Offset Inches 762 Projection dimensionsA1 a A2 a B2 a B1 aDistance Diagonal Height Width From screen Offset InchesConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting video source devicesConnecting a DVI-D device Connecting a Component Video source deviceTo connect the projector to a DVI-D device To connect the projector to a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/Composite Video source deviceStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image clarityUse / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Utilizing the password function Using a security cable lockSetting a password Securing the projectorEntering the password recall procedure If you forget the passwordChanging the password Write down the number and turn off your projectorBottom of the image Operation Disabling the password functionCorrecting keystone Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Selecting a color temperature Adjusting Brilliant ColorAbout color temperatures 3D Color ManagementSelection Description Setting the presentation timerPresentation Timer How to use the Timer On key? To cancel the timer, perform the following stepsUsing the remote control Top-Left Bottom-Left Top-Right Bottom-RightHiding the image Freezing the imageGo to the System Setup Basic Panel Key Lock Utilizing FAQ functionLocking control keys To exit the OSD menu, press MENU/EXITAdjusting the sound level Adjusting the soundTurning on the Power On/Off Ring Tone Operating in a high altitude environmentPersonalizing the projector menu display Configuring the Lan Control SettingsControlling the projector through a Lan environment If you are in a Dhcp environmentIf you are in a non-DHCP environment Ii. To switch input signal, click on your desired signalControlling the projector remotely through a web browser Iiii Iiiv Shutting down the projector Menu system Menu operationMain menu Sub-menu Options BasicAdvanced Control By RJ45/RS232 Closed Caption On/Off Enable Caption VersionProjector IP Lan Control AddressDescription of each menu Temperature Picture menu Function Description Picture ModeSave Settings ReferenceTimer System Setup Basic menu Function Description Quick AutoSettings Auto PowerCooling System Setup Advanced menu Function Description QuickHigh AltitudeReset All System Setup Advanced menu Function DescriptionClosed CaptionCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampRemove the lamp cover from the projector Replacing the lampLoosen the screws that secure the lamp Tighten the screw that secures the lamp Tighten the screws that secure the lamp cover Connect the power and restart the projectorResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsMm W x 127.87 mm H x 252 mm D DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmSupported timing for PC input Timing chartSupported timing for DVI-D & Hdmi Hdcp input Supported timing for Video and S-Video inputs Signal FormatSupported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directive

MP782 ST specifications

The BenQ MP782 ST is a versatile short-throw projector designed to enhance presentations and multimedia experiences in both classroom and corporate settings. This projector stands out for its high-definition display capabilities, compact design, and user-friendly features.

One of the key features of the MP782 ST is its short-throw projection technology. The projector can produce a large image from a short distance, allowing users to place it close to the wall or screen while still achieving a screen size of up to 100 inches. This makes it ideal for smaller rooms where space can be a constraint. The ability to project in tight spaces means that the audience can be closer to the image without the risk of casting shadows or obstructing the view.

In terms of image quality, the MP782 ST boasts a native resolution of 1280x800 (WXGA) and a brightness level of 3000 ANSI lumens. This combination ensures that images and presentations are clear and vibrant, even in well-lit environments. Additionally, the projector features a contrast ratio of 4000:1, allowing for deeper blacks and more vivid colors, which enhances the overall visual experience.

The MP782 ST is equipped with several advanced technologies that contribute to its impressive performance. Its SmartEco technology optimizes lamp power and extends the lifespan of the lamp up to 6000 hours, reducing maintenance costs and ensuring reliability during long presentations. Furthermore, the projector utilizes BrilliantColor technology, which enhances color accuracy and delivers more realistic images across various media types.

Connectivity is another strong suit of the BenQ MP782 ST. It features multiple input options, including HDMI, VGA, and USB, making it compatible with a variety of devices such as laptops, Blu-ray players, and document cameras. This versatility allows users to seamlessly integrate the projector into their existing technology setup.

The design of the MP782 ST also includes practical features for ease of use. It has a low fan noise level, ensuring that it operates quietly during presentations. Additionally, its lightweight construction makes it easily portable, allowing for flexibility in different settings, whether it be a classroom, conference room, or training facility.

Overall, the BenQ MP782 ST is a dynamic projector that combines short-throw technology, high brightness, and robust connectivity options to deliver a reliable and impressive presentation experience. Its thoughtful design and advanced features make it a strong choice for educators and business professionals alike, facilitating engaging and effective communication.
Top Page Image Contents