Dimensions, Mm W x 127.87 mm H x 252 mm D, Unit mm

BenQ MP782 ST Dimensions, Mm W x 127.87 mm H x 252 mm D, Ceiling Mount screw M4 x 8 Max L = 8 mm

Page 63

Dimensions

290 mm (W) x 127.87 mm (H) x 252 mm (D)

252 127.87

Ceiling mount installation

Ceiling Mount screw:

M4 x 8 (Max L = 8 mm)

	149.50
Unit: mm	75.95	62.34
Unit: mm

452.65	397.40	364.40
		84.00
		145.50

289.98

290

61.99

71.15

242.04

228.00

118.45

163.45

282.95

Specifications 63

Image 63

Contents

MP782 ST Digital Projector WelcomeTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedProjector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideLamp cover External control panel Projector Controls and functionsRemote control Locks the keys on the projector Auto ModeOperating the Laser pointer Toggles projector audio between on and offRemote control effective range Replacing the remote control batteriesApprox.+15 Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Page Projection dimensions A1 a A2 aDiagonal Height Width From screen Offset Inches 762 Diagonal Height Width From screen Offset Inches B1 aB2 a DistanceConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting audio Connecting video source devicesTo connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting a DVI-D device To connect the projector to a DVI-D deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/Composite Video source deviceStarting up the projector OperationFine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Securing the projector Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Correcting keystoneBottom of the image Operation Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Adjusting Brilliant ColorSelecting a color temperature About color temperaturesSetting the presentation timer Presentation TimerSelection Description Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsHow to use the Timer On key? Using the remote controlHiding the image Freezing the imageTo exit the OSD menu, press MENU/EXIT Utilizing FAQ functionGo to the System Setup Basic Panel Key Lock Locking control keysOperating in a high altitude environment Adjusting the soundAdjusting the sound level Turning on the Power On/Off Ring ToneIf you are in a Dhcp environment Configuring the Lan Control SettingsPersonalizing the projector menu display Controlling the projector through a Lan environmentIi. To switch input signal, click on your desired signal Controlling the projector remotely through a web browserIf you are in a non-DHCP environment Iiii Iiiv Shutting down the projector Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Lan Control Address Closed Caption On/Off Enable Caption VersionControl By RJ45/RS232 Projector IPDescription of each menu Reference Picture menu Function Description Picture ModeTemperature Save SettingsAuto Power System Setup Basic menu Function Description Quick AutoTimer SettingsAltitude System Setup Advanced menu Function Description QuickCooling HighCaption System Setup Advanced menu Function DescriptionReset All ClosedStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Loosen the screws that secure the lampRemove the lamp cover from the projector Tighten the screw that secures the lamp Connect the power and restart the projector Resetting the lamp timer Tighten the screws that secure the lamp cover Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsUnit mm DimensionsMm W x 127.87 mm H x 252 mm D Ceiling Mount screw M4 x 8 Max L = 8 mmSupported timing for PC input Timing chartSupported timing for DVI-D & Hdmi Hdcp input Signal Format Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement EEC statement

BenQ MP782 ST Dimensions, Mm W x 127.87 mm H x 252 mm D, Ceiling Mount screw M4 x 8 Max L = 8 mm