BenQ MX503, MS502 Switching input signal, Changing the password, Disabling the password function

Page 23

Changing the password

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced> Security Settings > Change Password menu.

2.Press MODE/ENTER. The message “INPUT CURRENT PASSWORD” appears.

3.Enter the old password.

i.If the password is correct, another message “INPUT NEW PASSWORD” displays.

ii.If the password is incorrect, the password error message displays lasting for three seconds, and the message “INPUT CURRENT PASSWORD” displays for your retry. You can press MENU/EXIT to cancel the change or try another password.

4.Enter a new password.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

5.Confirm the new password by re-entering the new password.

6.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.To leave the OSD menu, press MENU/EXIT.

Disabling the password function

To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Change Security Settings menu after opening the OSD menu system. Press MODE/ENTER. The message “INPUT PASSWORD” displays. Enter the current password.

i.If the password is correct, the OSD menu returns to the Security Settings page.

Press to highlight Power On Lock and press / to select Off. You will not have to enter the password next time when turning on the projector.

ii.If the password is incorrect, the password error message displays lasting for three seconds, and the message “INPUT PASSWORD” displays for your retry. You can press MENU/EXIT to cancel the change or try another

password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

Operation 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents MS502/MX503 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control battery Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableDiagonal Projection dimensionsObtaining a preferred projected image size Screen sizeConnection ConnectionComponent Video Better Good Normal Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusHighlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordDisabling the password function Switching input signalChanging the password Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Operation Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeAdjusting Brilliant Color Fine-tuning the image quality in user modes3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionLocking control keys Remote paging operationsFreezing the image Hiding the imageOperating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude ModeShutting down the projector Direct power offTurning off the Power On/Off Ring Tone Basic Menu operationMenu system Main menu Sub-menu OptionsMessage Time Sec Menu Settings Menu PositionRight/Bottom-Left Reminder On/OffAdvanced Description of each menu Display menu Picture menu Function Description Picture ModeTemperature 3D Color Management Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsScreen Panel KeyLock BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus CurrentSystem Care of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Off IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartVertical Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty Copyright

MX503, MS502 specifications

BenQ MX503 and MS502 are exemplary projectors that cater to the educational and office sectors with their cutting-edge features and technologies. These models are designed to offer exceptional projection quality and ease of use, ensuring that presentations, lectures, and meetings are impactful and engaging.

The BenQ MX503 boasts a native XGA resolution of 1024 x 768 pixels, providing crystal-clear images that enhance visual presentations. With a remarkable brightness of 3,000 ANSI lumens, it ensures that visuals remain vibrant and visible even in well-lit environments. The contrast ratio of 13,000:1 allows for deeper blacks and brighter whites, ensuring a more dynamic range in color representation. The projector is equipped with the Super Eco Mode technology, which reduces power consumption significantly, extending the lamp life to up to 10,000 hours, promoting energy efficiency.

On the other hand, the BenQ MS502 features SVGA resolution of 800 x 600 pixels, making it a more economical option while still delivering quality imagery suitable for various presentations. With a brightness of 3,000 ANSI lumens, the MS502 also guarantees visibility in diverse lighting conditions. Its contrast ratio reaches 2000:1, offering solid color depth and clarity, ideal for educational settings.

Both projectors incorporate 3D display technology, allowing users to present 3D content seamlessly, enhancing the learning experience and audience engagement. The easy installation feature, along with vertical keystone correction, simplifies the setup process, accommodating various room layouts.

Connectivity is another highlight of the MX503 and MS502 projectors, as they come with multiple input options, including VGA, HDMI, and USB ports, facilitating easy connection with laptops, desktop computers, and other multimedia devices. The intuitive user interface further streamlines navigation and operation.

In summary, the BenQ MX503 and MS502 projectors offer valuable features, including high brightness, energy-efficient operation, versatile connectivity, and superior image quality. They cater specifically to the needs of educational institutions and professional environments, making them reliable choices for anyone looking to enhance their presentation delivery. With a focus on performance and user-friendliness, these projectors stand out in their category, meeting demanding visual presentation needs effectively.
Top Page Image Contents