BenQ MX503, MS502 user manual Timing of replacing the lamp, Status Message

Page 45

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com for a replacement lamp.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 49 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

Install a new lamp for optimal performance. If the

Notice

projector is normally run with Economic

 

selected (See "Getting to know the lamp hour" on

Order Replacement Lamp

page 44), you may continue to operate the

Lamp>XXXX Hours

projector until the next hour lamp warning

 

appears.

Order a new lamp at lamp.benq.com

Press MODE/ENTER to dismiss the message.

OK

 

 

It is strongly recommended that you replace the

Notice

lamp at this age. The lamp is a consumable item.

 

The lamp brightness diminishes with use. This is

Replace Lamp Soon

normal lamp behavior. You can replace the lamp

 

whenever you notice that the brightness level has

Lamp>XXXX Hours

 

significantly diminished.

Order a new lamp at lamp.benq.com

Press MODE/ENTER to dismiss the message.

OK

 

Notice

 

Replace Lamp Now

 

Lamp>XXXX Hours

 

Lamp usage time exceeded

 

Order a new lamp at lamp.benq.com

 

OK

 

 

The lamp MUST be replaced before the projector

WARNING

will operate normally.

Out of Lamp Usage Time

Press MODE/ENTER to dismiss the message.

 

 

Replace lamp (Refer to user manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

"XXXX" shown in the above messages are numbers that vary depending on different models.

Maintenance 45

Image 45
Contents MS502/MX503 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control battery Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size DiagonalConnection ConnectionConnecting audio Connecting video source devicesTerminal name Terminal appearance Component Video Better Good NormalStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Below is the overview of the OSD menu Using the menusUtilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordSwitching input signal Changing the passwordDisabling the password function Selecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Operation Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modes3D Color Management To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-RightFreezing the image Remote paging operationsHiding the image Locking control keysAdjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentDirect power off Turning off the Power On/Off Ring ToneShutting down the projector Menu system Menu operationMain menu Sub-menu Options BasicRight/Bottom-Left Time Sec Menu Settings Menu PositionReminder On/Off MessageAdvanced Description of each menu Temperature 3D Color Picture ModeManagement Save Settings Display menu Picture menu Function DescriptionTimer System Setup Basic menu Function Description Quick AutoSettings SearchLock Panel KeyBackground ScreenReset All System Setup Advanced menu Function DescriptionBaud Rate Test PatternCurrent SystemStatus Care of the projector MaintenanceLamp information Setting Lamp Mode as EconomicGetting to know the lamp hour Extending lamp lifeStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Resetting the lamp timer Light Status & Description Power events IndicatorsLamp events OffTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Vertical HorizontalLimited warranty Warranty and Copyright informationCopyright Disclaimer

MX503, MS502 specifications

BenQ MX503 and MS502 are exemplary projectors that cater to the educational and office sectors with their cutting-edge features and technologies. These models are designed to offer exceptional projection quality and ease of use, ensuring that presentations, lectures, and meetings are impactful and engaging.

The BenQ MX503 boasts a native XGA resolution of 1024 x 768 pixels, providing crystal-clear images that enhance visual presentations. With a remarkable brightness of 3,000 ANSI lumens, it ensures that visuals remain vibrant and visible even in well-lit environments. The contrast ratio of 13,000:1 allows for deeper blacks and brighter whites, ensuring a more dynamic range in color representation. The projector is equipped with the Super Eco Mode technology, which reduces power consumption significantly, extending the lamp life to up to 10,000 hours, promoting energy efficiency.

On the other hand, the BenQ MS502 features SVGA resolution of 800 x 600 pixels, making it a more economical option while still delivering quality imagery suitable for various presentations. With a brightness of 3,000 ANSI lumens, the MS502 also guarantees visibility in diverse lighting conditions. Its contrast ratio reaches 2000:1, offering solid color depth and clarity, ideal for educational settings.

Both projectors incorporate 3D display technology, allowing users to present 3D content seamlessly, enhancing the learning experience and audience engagement. The easy installation feature, along with vertical keystone correction, simplifies the setup process, accommodating various room layouts.

Connectivity is another highlight of the MX503 and MS502 projectors, as they come with multiple input options, including VGA, HDMI, and USB ports, facilitating easy connection with laptops, desktop computers, and other multimedia devices. The intuitive user interface further streamlines navigation and operation.

In summary, the BenQ MX503 and MS502 projectors offer valuable features, including high brightness, energy-efficient operation, versatile connectivity, and superior image quality. They cater specifically to the needs of educational institutions and professional environments, making them reliable choices for anyone looking to enhance their presentation delivery. With a focus on performance and user-friendliness, these projectors stand out in their category, meeting demanding visual presentation needs effectively.