BenQ CP220 Remote control effective range, Replacing the remote control battery, Front Rear

Page 16

Remote control effective range

Infra-Red (IR) remote control sensors are located on the front and the back of the projector. The remote control must be held at an angle within 30 degrees of the projector’s IR remote control sensors to function correctly. The distance between the remote control and the sensors should not exceed 6 meters (~ 20 feet).

Make sure that there are no obstacles between the remote control and the IR sensors on the projector that might obstruct the infra-red beam.

•

Operating the projector from the

•

Operating the projector from the

 

front

 

rear

 

 

 

°

 

 

 

 

 

 

x.15

 

 

 

 

 

ro

 

 

 

 

 

pp

 

 

 

 

 

 

A

 

 

 

 

 

 

°

 

 

 

 

 

 

x.15

 

 

 

 

 

ro

 

 

 

 

 

pp

 

 

 

 

 

 

A

 

 

 

Replacing the remote control battery

1.Pull out the battery holder.

2.Insert the new battery in the holder. Note the positive polarity should face outward.

3.Push the holder into the remote control.

•Avoid leaving the remote control and

battery in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.

•Replace only with the same or equivalent type recommended by the battery manufacturer.

•Dispose of the used battery according to the manufacturer’s instructions.

•Never throw the battery into a fire. There may be danger of an explosion.

•If the battery is dead or if you will not be using the remote control for an extended period of time, remove the battery to avoid damage to the remote control from possible battery

leakage.

10 Introduction

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Welcome Copyright DisclaimerTable of contents Switching input signal Adjusting the projected image Iv Table of contentsTable of contents Supported timing for Component-YPbPr inputMemo Vi Table of contents Important safety instructions Safety Instructions Bedding or any other soft surface Safety Instructions Introduction Projector featuresIntroduction Shipping contents Projector exterior view Front / upper sideRear side Lower/ Side viewPower indicator light See Indicators on page 42 for details Controls and functionsProjector Keystone / Left Keystone / RightRemote control Keystone SeeTurns the projector on or off Up, Down Left, RightRemote control effective range Replacing the remote control batteryOperating the projector from Front RearSafety instructions for ceiling mounting of the projector Positioning your projectorChoosing a location Floor frontObtaining a preferred projected image size Positioning your projector Maximum zoom Minimum zoom Screen Center of lens Projection distance1219 1500Connecting a computer or monitor Connecting a computerConnection ConnectionConnecting a monitor Connecting Video source devices Best video qualityConnecting a Component Video source device 1080i 50/ 60 HzConnecting an S-Video source device Settings. See Mute Off and Volume 5 on page 35 for detailsConnecting a composite Video source device Plug the power cord into the projector and into a wall OperationStart up OperationSetting a password Utilizing the password functionIf you forget the password Switching input signal Entering the password recall procedureChanging the password Closing the password functionAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityOptimizing the image Correcting keystoneSelecting an application mode PC Signal InputOther adjustments Adjusting brightnessOperating in a high altitude environment Current StatusHiding the image Remote paging operationsFreezing the image Personalizing the projector menu displayDisconnect the power cord from the wall socket Shutting down the projectorMenu operation Menu systemUsing the menus On the remote control to leaveSave the setting Right on the projector or Press Exit on the projectorPicture menu Pro-Picture menu Setting menu Advance menu Resolution Mode EquivalentInformation menu SourceMaintenance Care of the projectorLamp information Calculation of lamp hourReplacing the lamp Resetting the lamp counter Temperature information IndicatorsPower indicator light is flashing during powering up Projector is under normal operationProjector needs 90 seconds to cool down. Or Please contact your dealer for assistanceTroubleshooting Plug the power cord into the AC inlet onMake sure that it is switched on Lens cover is not open Slide open the lens coverSpecifications Projector specificationsTiming chart Supported timing for PC inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsDimensions Unit mm SpecificationsWarranty Limited WarrantyRegulation Statements FCC statementEEC statement MIC statement

CP220 specifications

The BenQ CP220 is a robust and reliable projector designed for educational and business environments. This model is renowned for its exceptional image quality, ensuring that presentations are both clear and engaging. Equipped with DLP (Digital Light Processing) technology, the CP220 utilizes a high-brightness lamp that provides vivid colors and sharp details. With a brightness rating of 2500 ANSI lumens, it excels in various lighting conditions, making it suitable for both small and large venues.

One of the standout features of the BenQ CP220 is its native XGA resolution of 1024x768 pixels, which allows for detailed display of text and images. This resolution is particularly beneficial for presenting high-definition content, ensuring that every detail is captured and displayed accurately. Additionally, the projector supports a range of resolutions and aspect ratios, making it versatile for differing media formats.

The CP220 is designed with user convenience in mind. It features quick and easy setup options, including automatic keystone correction, which ensures that images are perfectly aligned, regardless of the projector's angle. This feature is particularly useful in dynamic environments where quick adjustments are often needed. Furthermore, the projector offers a multitude of connectivity options, including VGA, USB, and HDMI ports, allowing users to connect a variety of devices seamlessly.

In terms of durability and maintenance, the BenQ CP220 boasts a long lamp life of up to 4,500 hours in economy mode. This means less frequent lamp replacements and lower overall operating costs, which is an important consideration for educational institutions and businesses looking to maximize their investments. The projector's efficient cooling system also helps to ensure longer operational periods without overheating.

Overall, the BenQ CP220 stands out for its combination of performance, versatility, and user-friendly features. Its high brightness, excellent resolution, and ease of use make it an ideal choice for any setting that demands reliable and high-quality projector performance. Whether for classroom instruction, corporate presentations, or multimedia displays, the CP220 is a dependable tool that enhances communication and engagement. With its advanced technologies and thoughtful design, the BenQ CP220 continues to be a favored choice among educators and professionals alike.
Top Page Image Contents