BenQ model gp1 user manual Entering the password recall procedure, Changing the password

Page 23

Entering the password recall procedure

1.Press and hold AUTO on the remote control for 3 seconds. The projector will display a coded number on the screen.

2.Write down the number and turn off your projector.

3.Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

Changing the password

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings > Change password menu.

2.Press MODE/ENTER. The message 'INPUT CURRENT PASSWORD' displays.

3.Enter the old password.

If the password is correct, another message 'INPUT NEW PASSWORD' displays.

If the password is incorrect, the password error message displays lasting for three seconds, and the message 'INPUT CURRENT PASSWORD' displays for your retry. You can press MENU/EXIT to cancel the change or try another password.

4.Enter a new password.

The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

5.Confirm the new password by re-entering the new password.

6.You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.To leave the OSD menu, press MENU/EXIT.

Disabling the password function

To disable password protection, go back to the SYSTEM SETUP: Advanced > Security Settings > Power on lock menu after opening the OSD menu system. Select Off by pressing

/ . The message 'INPUT PASSWORD' displays. Enter the current password.

If the password is correct, the OSD menu returns to the Security Settings page with 'Off' shown in the row of Power on lock. You will not have to enter the password next time you turn on the projector.

If the password is incorrect, the password error message displays lasting for three seconds, and the message 'INPUT PASSWORD' displays for your retry. You can press MENU/EXIT to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Operation 23

Image 23
Contents Welcome Table of contents Do not look straight at the projector Important safety instructionsRefer servicing to qualified service Operate your projector. Save it forSafety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewControls and functions Projector PowerPower and Ring LED indicator Volume/Arrow keys /-, /+ Key LED indicatorReturn Remote controlKeystone/Arrow keys / Up Down SelectRemote control effective range Obtaining a preferred projected image size Positioning your projectorFeet Projection dimensionsTo connect the projector to a notebook or desktop computer Connecting a computerConnection Least video quality Connecting Video source devicesBest video quality To connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceUSB flash disk Connecting a USB Reader source deviceStarting up the projector OperationUse / to highlight the System Setup Basic menu Using the menusIf you forget the password Utilizing the password functionSetting a password Disabling the password function Entering the password recall procedureChanging the password Adjusting the image height Switching input signalAdjusting the projected image Correcting keystone Auto-adjusting the imageFine-tuning the image clarity Selecting the aspect ratio Magnifying and searching for detailsOptimizing the image Selecting a picture modePicture modes for different types of signals Go to the Picture Picture Mode menu Setting the User modeFine-tuning the image quality in user modes Using Wall ColorFreezing the image Hiding the imageOperating in a high altitude environment Adjusting the soundAdjusting the sound level System Setup Advanced menu isShutting down the projector Personalizing the projector menu displaySimple menu system Projector menu operationBasic Complete menu systemAdvanced Description of each menu Reference Picture ModeTemperature Save Settings Picture menu3Quick Auto Auto PowerBlank Timer Sleep TimerAudio SettingsReset All Advanced menuCurrent FAQ-Image InstallationFeatures Service Information menuPlaying back photos and movies Presenting From a USB ReaderEntering USB Reader main screen PC-less presentations Using USB Reader menus Use / to highlight Custom Setup menu USB Reader menu system USB Reader menu operationManager mode Setup menuEnter File Manager mode Extension Detail USB Reader support formatSubtitle Audio Codec DetailMovie Care of the projector MaintenanceStatus / Problems LED indicators Ring Power Key IndicatorsTroubleshooting Projector specifications SpecificationsTiming chart DimensionsLimited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements