BenQ W10000, W9000 manual Specifications, Dimensions

Page 37

English

Specifications

All specifications are subject to change without notice.

Optical

Projection system DMD chip Lens

Projection screen size Lamp

Single-chip DLPTM system. 0.95" DLP (1920 x 1080) 1.15x zoom

23.5" ~ 300" 250W

Electrical

Video Signal	NTSC / NTSC4.43 / PAL-M / PAL-N / SECAM / DTV
Data Signal	WXGA, SXGA, XGA, SVGA, VGA, VESA,
	Macintosh® 16"/13" and 21"/19"(in Advanced Intelligent Compression),
	HDTV compatible (1080p, 1080i, 720p, 576p, 576i, 480p, 480i)
Max. number of display colors	16,770,000 (full color display)

Terminals

Input	Video, S-Video, Component (Y/ CB/ CR, Y/ PB/ PR) RS-232C, RGBHV,
	HDMI
Output	12VDC

General characteristics

Weight	20.9lbs / 9.5kg
Power	VAC 100 - 240V, 4.0 A, 50 / 60 Hz (Automatic)
Power consumption	Max 370W
Operating temperature	0 °C to 40 °C at sea level
Operating humidity	10% - 90% (without condensation)
Operating altitude	6000 feet at 30°C, 6000 - 10000 feet at max. 23°C
Storage temperature	-10°C- 60°C / 14°F to 140°F
Storage humidity	10% - 90%

Dimensions

492 x 195 x 444 mm (W x H x D) with the cable connector-panel cover attached 492 x 195 x 393 mm (W x H x D) without the cable connector-panel cover attached

	492
444	393 195

Unit: mm

37 Additional information

Image 37

Contents W10000/W9000 Digital Projector Home Cinema Series WelcomeCopyright WarrantyDisclaimer Table of contents Using the menus Picture menu Display menu Fine-tuning the image size and claritySetup menu Advance menu IndicatorsSafety, regulatory and legal information Safety instructions Safety instructionsDuring operation. It may harm your sight Do not block the ventilation holes whileDo not step on the projector or place any objects upon it English Remote control batteries Shipping contentsOverview Full HD compatible BenQ W10000/W9000 projector featuresProjector exterior view Connector panelFront and upper side view Rear viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorFloor front Floor rearWidescreen ratio screen dimension table Installation for a 169 ratio screenObtaining a preferred projected image size Diagonal Width Height Min distance withStandard ratio screen dimension table Installation for a 43 ratio screenShifting the projection lens vertically Top level of the projected imagesConnecting a computer Connecting with video equipmentConnect the projector to a computer with a VGA-BNC cable Connecting Hdmi devices Connecting video inputsConnecting component-video devices Connecting S-Video or video devicesAdjusting the projected image Using the projectorPreparations Turning the projector onSelecting a preset mode Fine-tuning the image size and clarityOptimizing the image Selecting the aspect ratioAdjusting contrast ratio Using Panamorph lenses optional Other adjustmentsDisplaying more than one image source simultaneously Aspect ratio image Aspect ration imagePersonalizing the projector menu display Turning the power offSaving and loading the video memory POPOn Screen Display OSD structure MenusFollowing example describes the adjustment of the keystone Using the menusPicture menu Extended Picture SettingsPIP Display menuPOP VideoOptions menu Setup menuLamp Dust FilterIv. Repeat steps ii and iii for other color adjustments To adjust and store the settingsAdvance menu Vii. Exit the OSD menuEnglish Care of the projector Additional informationRemote control is pressed To clean the filterRe-install the filter grill and cover securely To install the cover Installing the cable connector-panel coverSection. See page 32 for details Both sides. Loosen the screwsLamp cover located on the left side Replacing the lampTighten the screws securing the lamp box When the projector is in a normal state IndicatorsWhen the projector is in an abnormal state Projector does TroubleshootingImage is unstable Picture is blurredDimensions Specifications