BenQ MX720 System Setup Advanced menu Function Description, Standby, Network, Reset All

Page 46

5. SYSTEM SETUP: Advanced menu

Function

Description

 

Network

 

Selecting On enables the function. The projector is able to provide the

 

network function when it is in standby mode.

 

Microphone

 

Selecting On enables the function. The projector can output the

 

microphone signal when it is in standby mode and all the necessary

 

equipment is correctly connected. See "Playing sound through the

 

projector" on page 17 for details.

Standby

Monitor Out

Selecting On enables the function. The projector can output a VGA

Settings

signal when it is in standby mode and the COMPUTER 1 jack is

 

correctly connected to devices. See "Connection" on page 16 for how

 

to make the connection.

 

Audio Pass Through

 

The projector can play sound when it is in standby mode and the

 

corresponding jacks are correctly connected to devices. Press / to

 

choose the source that you wish to use. See "Connection" on page 16

 

for how to make the connection.

 

Enabling this function slightly increases the standby power consumption.

 

 

 

Wired LAN

 

Projection Log In Code

 

See BenQ Network Projector Operation Guide for details.

Network

AMX Device Discovery

Settings

When AMX Device Discovery is On, the projector can be detected

 

by AMX controller.

 

MAC Address

 

Displays the mac address for this projector.

Reset All

Returns all settings to the factory preset values.

The following settings will still remain: Position, Phase, H. Size, Projector

Settings

Installation, Color Space Conversion, High Altitude Mode, Security

 

Settings, Baud Rate and Network Settings.

 

 

46 Operation

Page 45 Page 47
Image 46
Page 45 Page 47
Contents
MX720/MW721 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions ProjectorRemote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingObtaining a preferred projected image size MX720MW721 Connection ConnectionConnecting audio Connecting video source devicesPlaying sound through the projector About the microphone input Audio output portOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio MX720 MW721Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a Color Temperature Setting a preferred color temperature 3D Color ManagementResetting current or all picture modes Setting the presentation timerSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentUsing the test pattern Adjusting the soundTurning off the Power On/Off Ring Tone Using the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Basic Main menu Sub-menu Options System Setup Advanced Operation Description of each menu Color Temperature Picture menu Function Description Picture Mode Temperature Fine Tuning 3D ColorSettings TimerInstallation SearchRemote System Setup Basic menu Function DescriptionOperation ReceiverAudio System Setup Advanced menu Function Description HighAltitude LampStandby System Setup Advanced menu Function DescriptionReset All NetworkSystem CurrentStatus Maintenance Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Resetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YP bP r inputTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer
Related manuals
Manual 61 pages 54.58 Kb
Top Page Image Contents