BenQ MX812ST, MW811ST user manual Replacing the lamp

Page 67

Replacing the lamp

•To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

•To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

•To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.

•To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the empty lamp compartment when the lamp is removed.

•This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper manner.

•To assure optimal performance from the projector, it is recommended that you purchase a qualified projector lamp for lamp replacement.

•If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by fractured lamp.

1.Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2.Loosen the screw that secures the lamp

cover on the side of the projector until the lamp cover loosens.

3.Remove the lamp cover from the

 

projector.

1

4.

Remove and dispose of the lamp

 

protection film.

2

• Do not turn the power on with the lamp cover

 

removed.

 

•Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries.

5.Disconnect the lamp connector from the

projector as illustrated.

6. Loosen the screw that secures the lamp.

3

2

1

Maintenance 67

Page 66 Page 68
Image 67
Page 66 Page 68
Contents Model Name MX713 ST/MW714 ST/MX762 ST Digital ProjectorTable of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedIntroduction Projector featuresIntroduction Shipping contents Front/upper side Rear/lower side Projector exterior viewProjector Controls and functionsKeystone/Arrow buttons / Up Down Remote controlTest AutoNumeric buttons Operating the Laser pointerMute MIC/VOL +Replacing the remote control batteries Remote control effective rangeApprox.+15º Front Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsDiagonal Height Width From screen Offset 1270 MW714 ST1107 623 150 3810 2286 3048 1905 1490 180 4572 2743 3658 1787 B1 aB2 a Distance150 3810 2019 3231 2032 1077 1723100 2540 1346 2154 120 3048 1615 2585Connection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceAbout the microphone input Playing sound through the projectorDevice Page Starting up the projector OperationOperation Fine-tuning the image clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space MX762 ST only Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volumeIf you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Advanced Network Description of each menu Display menu Picture menu Function Description Picture ModeTemperature Management Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsLock Settings Security DescriptionPanel Key BackgroundTest Pattern System Setup Advanced menu Function DescriptionReset All Baud RateStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Page Resetting the lamp timer Connect the power and restart the projectorTighten the screw that secures the lamp cover Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mm DimensionsCeiling mount installation Mm W x 128 mm H x 252 mm D 290Supported timing for PC input Timing chartSupported timing for Hdmi Hdcp input-MX762 ST only Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users

MX812ST, MW811ST specifications

The BenQ MW811ST and MX812ST are two powerful projectors designed for education and business presentations, offering multiple features that enhance the viewing experience. Both models showcase BenQ's commitment to delivering exceptional image quality and user-friendly functionalities.

Starting with the MW811ST, this projector boasts a WXGA resolution of 1280x800 pixels, providing a widescreen aspect ratio perfect for displaying HD content. With a brightness of 3000 ANSI lumens, it ensures vibrant images even in well-lit environments. The short-throw capability of this model allows users to project large images from a short distance, making it ideal for smaller classrooms and meeting rooms. The lens produces a screen size of up to 100 inches from only a short distance of about 1.5 meters, maximizing space efficiency.

The MW811ST also features BenQ's exclusive SmartEco technology, which intelligently adjusts lamp power and brightness according to the content being displayed. This results in significant power savings and prolonged lamp life, reducing total cost of ownership. The projector provides lamp life of up to 6000 hours in eco mode, ensuring extended usage between replacements. Additionally, it supports 3D content, providing a more immersive experience for viewers.

On the other hand, the BenQ MX812ST is equipped with XGA resolution of 1024x768 pixels. It offers a similar brightness of 3200 ANSI lumens, delivering clear visuals in various lighting conditions. Like the MW811ST, the MX812ST features short-throw projection capabilities, making it suitable for tight environments where space is limited. The projector can display a large image from a short distance, emphasizing convenience and practicality.

The MX812ST also includes essential features such as the SmartEco technology for energy efficiency and extended lamp life. Both models seamlessly integrate with an array of devices, including laptops and streaming devices, ensuring versatile compatibility in various presentation settings. Additionally, the user-friendly interface and remote control simplify navigation for users, making the projector easy to operate.

In conclusion, the BenQ MW811ST and MX812ST projectors deliver outstanding image quality, flexibility, and convenience, making them excellent choices for educators and professionals. Their robust features, integrated technologies, and energy-efficient designs position them as reliable tools for delivering effective and engaging presentations.
Top Page Image Contents