BenQ MW811ST, MX812ST Controlling the projector through a LAN environment, Cable connection

Page 40

Controlling the projector through a LAN environment

You can manage and control the projector from one or more remote computers when they are properly connected to the same local area network.

Cable/ADSL Internet modem

Cable connection

If you are in a DHCP environment:

1.Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port on your Ethernet or router.

2.Do one of the following:

•Press NETWORK SETTING on the remote control. The Network Settings page is displayed.

•Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced

menu is highlighted. Press to highlight Network Settings and press MODE/ ENTER. The Network Settings page is displayed.

3.Highlight Wired LAN and press MODE/ENTER.

4.Make sure the Status is Connect.

5.Press to highlight DHCP and press / to select On.

6.Press to highlight Apply and press MODE/ENTER.

7.Re-enter the Network Settings > Wired LAN page. The IP Address, Subnet Mask, Default Gateway, and DNS settings will be displayed. Note down the IP address displayed in the IP Address row.

If the IP Address still does not appear, contact your ITS administrator.

If you are in a non-DHCP environment:

1.Repeat steps 1-4above.

2.Press to highlight DHCP and press / to select Off.

3.Contact your ITS administrator for information on the IP Address, Subnet Mask, Default Gateway, and DNS settings.

4.Press to select the item you want to modify and press MODE/ENTER.

5.Press / to move the cursor and the press / to enter the value.

6.To save the settings, press MODE/ENTER. If you do not want to save the settings, press MENU/EXIT.

7.Press to highlight Apply and press MODE/ENTER.

40 Operation

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Digital Projector Model Name MX713 ST/MW714 ST/MX762 STTable of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions ProjectorRemote control TestAuto Keystone/Arrow buttons / Up DownOperating the Laser pointer MuteMIC/VOL + Numeric buttonsReplacing the remote control batteries Remote control effective rangeApprox.+15º Positioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeDiagonal Height Width From screen Offset 1270 MW714 ST1107 623 B1 a B2 aDistance 150 3810 2286 3048 1905 1490 180 4572 2743 3658 17872032 1077 1723 100 2540 1346 2154120 3048 1615 2585 150 3810 2019 3231Connection Connecting video source devices Connecting audioTerminal name Terminal appearance BestAbout the microphone input Playing sound through the projectorDevice Page Starting up the projector OperationOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureChanging the password Write down the number and turn off your projectorDisabling the password function Switching input signal Changing Color Space MX762 ST onlyMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageTo activate the High Altitude Mode Using the remote controlLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelAdjusting the microphone volume Turning off the Power On/Off Ring ToneControlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environmentWireless connection Highlight Wireless LAN and press MODE/ENTERControlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu operation Menu systemMain menu Sub-menu Options BasicAdvanced Advanced Network Description of each menu Picture Mode TemperatureManagement Save Settings Display menu Picture menu Function DescriptionSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchSettings Security Description Panel KeyBackground LockSystem Setup Advanced menu Function Description Reset AllBaud Rate Test PatternFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Page Resetting the lamp timer Connect the power and restart the projectorTighten the screw that secures the lamp cover Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationMm W x 128 mm H x 252 mm D 290 Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input-MX762 ST only Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive

MX812ST, MW811ST specifications

The BenQ MW811ST and MX812ST are two powerful projectors designed for education and business presentations, offering multiple features that enhance the viewing experience. Both models showcase BenQ's commitment to delivering exceptional image quality and user-friendly functionalities.

Starting with the MW811ST, this projector boasts a WXGA resolution of 1280x800 pixels, providing a widescreen aspect ratio perfect for displaying HD content. With a brightness of 3000 ANSI lumens, it ensures vibrant images even in well-lit environments. The short-throw capability of this model allows users to project large images from a short distance, making it ideal for smaller classrooms and meeting rooms. The lens produces a screen size of up to 100 inches from only a short distance of about 1.5 meters, maximizing space efficiency.

The MW811ST also features BenQ's exclusive SmartEco technology, which intelligently adjusts lamp power and brightness according to the content being displayed. This results in significant power savings and prolonged lamp life, reducing total cost of ownership. The projector provides lamp life of up to 6000 hours in eco mode, ensuring extended usage between replacements. Additionally, it supports 3D content, providing a more immersive experience for viewers.

On the other hand, the BenQ MX812ST is equipped with XGA resolution of 1024x768 pixels. It offers a similar brightness of 3200 ANSI lumens, delivering clear visuals in various lighting conditions. Like the MW811ST, the MX812ST features short-throw projection capabilities, making it suitable for tight environments where space is limited. The projector can display a large image from a short distance, emphasizing convenience and practicality.

The MX812ST also includes essential features such as the SmartEco technology for energy efficiency and extended lamp life. Both models seamlessly integrate with an array of devices, including laptops and streaming devices, ensuring versatile compatibility in various presentation settings. Additionally, the user-friendly interface and remote control simplify navigation for users, making the projector easy to operate.

In conclusion, the BenQ MW811ST and MX812ST projectors deliver outstanding image quality, flexibility, and convenience, making them excellent choices for educators and professionals. Their robust features, integrated technologies, and energy-efficient designs position them as reliable tools for delivering effective and engaging presentations.
Top Page Image Contents