BenQ W770ST user manual Specifications, Optical, Electrical, Mechanical, Output terminals, Control

Page 55

Specifications

All specifications are subject to change without notice.

Optical

Resolution

1280 (H) x 720 (V) Display system

Single-chip DLPTM system Lens F/Number

W750

F = 2.54 to 2.73, f = 18.18 to 21.84 mm

W770ST

F = 2.6 to 2.78, f = 10.2 to 12.24 mm

Lamp

210 W lamp

Electrical

Power supply

AC100–240V, 3.2 A, 50-60 Hz (Automatic) Power consumption

295 W (Max); < 0.5 W (Standby)

Mechanical

Weight

W750

2.6 Kg (5.73 lbs)

W770ST

2.7 Kg (5.95 lbs)

Output terminals

Speaker

(Stereo) 10 watt x 1 Audio signal output

PC audio jack x 1

Control

RS-232 serial control 9 pin x 1

IR receiver x 2

Mini B type USB x 1 (Used for service)

Input terminals

Computer input RGB input

D-Sub 15-pin (female) x 1

Video signal input

S-VIDEO

Mini DIN 4-pin port x 1

VIDEO

RCA jack x 1 SD/HDTV signal input

Analog - Component RCA jack x 3 (through RGB input)

Digital - HDMI x 2

Audio signal input Audio in

RCA audio jack (L/R) x 2

Environmental Requirements

Operating temperature 0°C–40°C at sea level

Operating relative humidity 10%–90% (without condensation)

Operating altitude 0–1499 m at 0°C–35°C 1500–3000 m at 23°C–30°C (with High Altitude Mode on)

Using the projector

55

Image 55

Contents User Manual W750/W770ST Digital Projector Home Cinema SeriesPositioning your projector Table of contentsConnecting with video Warranty and CopyrightImportant safety instructions Do not cover the projector with any item Lead, which is contained in solder Mercury, which is used in the lamp Moisture condensationAvoid volatile liquids DisposalRemote control Shipping contentsOverview Some of the accessories may vary from region to regionRemote control effective range Replacing the remote control batteriesCeiling mounting the projector 8 Overview Vivid color reproduction Projector featuresHigh picture quality High brightnessRear and lower side view Projector exterior viewSee Connecting with video equipment on page 19 for connection details Front and upper side viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorObtaining a preferred projected image size How to determine the recommended screen size for a given distanceWidth Projection dimensionsDiagonal Heightinch Vertical offsetlens Installation for a 43 ratio screenLowest ImageHeight Connecting HDMI devices Connecting with video equipmentPreparations Connecting S-Video or video devices Connecting component-video devices20 Positioning your projector Connect the projector to a computer with a VGA cable Connecting a computerTurning the projector on Using the projectorSelecting an input source Fine-tuning the image size and clarityENTER Using a security cable lock Using the menusSecuring the projector Input Password page displays Utilizing the password functionSetting a password If you forget the password26 Using the projector Entering the password recall procedureChanging the password Disabling the password functionAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Setting the User 1/User 2/User 3 mode Using the preset and user modesSelecting a preset mode Fine-tuning the selected picture modeAdjusting Contrast Fine-tuning the picture qualityResetting the picture mode Adjusting BrightnessSelecting a color temperature Adjusting ColorAdjusting Tint Adjusting SharpnessControlling image clarity Advanced picture quality controlsSetting Black Level Setting a preferred color temperatureAdjusting Brilliant Color Selecting a Gamma settingColor Management Setting 3D Comb Filter Setting Film Modeamong Red , Green , Blue , Cyan , Magenta and Yellow Muting the sound Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneAbout the aspect ratio Selecting the aspect ratioOSD menus can be displayed on those unused black areas Magnifying and searching for detailsUsing the 3D menus Watching 3D contentOperating in a high altitude environment Connecting 3D video devicesStop watching 3D content if you feel fatigue or discomfort Take appropriate breaks when watching 3D contentLocking control keys Personalizing the projector menu displayTurning the projector off Cinema/Dynamic/Standard/User 1/User 2/User 3/3D On-Screen Display OSD menusPreset Mode On-Screen Display OSD structureInformation System SetupBasic AdvancedPicture menu Display menu Audio Setup menuSystem Setup Basic menu Closed Caption Enable System Setup Advanced menuReset Lamp Timer Resetting the lamp timer on page 51 for detailsThis menu shows you the current operating status of the projector Information menuCare of the projector Additional informationGetting to know the lamp hour Lamp informationExtending lamp life until the next hour lamp warning appears Timing of replacing the lampReplacing the lamp Install a new lamp for optimal performance. If the projector isLift the handle so that it stands up Disconnect the lamp connector from the projector3. Remove the lamp cover from the projector Loosen the screw that secures the lampResetting the lamp timer Power IndicatorsPowering up The projector needs to cool for 90 seconds after the powerThe projector may be in a poorly ventilated location The internal temperature is too highThe intake ventilation or the exhaust ventilation is blockednecessary. See page Troubleshootingswitched on. See page ring. See pageMechanical SpecificationsOptical Electrical76.5 Unit mmCeiling mount screws M6 x 8 Max. L = 8 mm 127.7253.47 74.5102.84 133.97BenQ Notebook FrequencyXGA60 XGA120Supported timing for 3D signal with Top-Bottom and Side-by-Side format BenQ Notebook Pixel Freq. MHz Supported timing for 3D signal with Side-by-Side formatRefresh rate Hz H. Freq. KHzNTSC 62 Using the projectorSupported timing for EDTV and HDTV via Component inputs Supported timing for Video and S-Video inputsDisclaimer Warranty and Copyright informationWarranty Copyright