BenQ MS614, MX615 user manual Connection

Page 15

Connection

When connecting a signal source to the projector, be sure to:

1.Turn all equipment off before making any connections.

2.Use the correct signal cables for each source.

3.Ensure the cables are firmly inserted.

•In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 8). They are commercially available from electronics stores.

•The connection illustrations below are for reference only. The rear connecting jacks available on the projector vary with each projector model.

Notebook or desktop computer

Monitor

A/V device

(VGA)		(DVI)
1	2	3	1	8						Speakers	8



				10	4	8	5	6	7
				10	4	8	5	6	7
		9						or
								or

1.VGA cable

2.VGA to DVI-A cable

3.USB cable

4.Component Video to VGA (D-Sub) adapter cable

5.S-Video cable

6.Video cable

7.Audio L/R cable

8.Audio cable

9.USB flash drive/USB wireless dongle

10.HDMI cable

Connection 15

Image 15

Contents Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedProjector features IntroductionIntroduction Shipping contents Front/upper side Projector exterior viewProjector Controls and functionsFreeze Volume +Timer On Timer Set upPpr 15º Remote control effective rangeReplacing the remote control battery Pull out the battery holderFront Ceiling Positioning your projectorChoosing a location Front TableVertical Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm DiagonalConnection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceOperation Starting up the projectorOperation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageTo correct keystoning at the bottom of the image Correcting keystoneUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Enter a new password Changing the passwordDisabling the password function Enter the old passwordChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageCreating your own startup screen To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneControlling the projector through a LAN environment Wireless connectionPage Page Page Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Standby Network On/Off Closed Caption On/Off Enable Caption VersionSettings Monitor Out On/Off Wireless LANDescription of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsSplash Panel KeyBackground LockBaud Rate System Setup Advanced menu Function DescriptionWireless Reset AllStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampLamp cover loosens Remove the lamp cover from Projector.1 Replacing the lampUse the handle to slowly pull the lamp out Projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsUnit mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Ceiling Mount screw M4 x 8 Max L = 8 mmSupported timing for PC input Timing chart1360 x Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users

MS614, MX615 specifications

The BenQ MX615 and MS614 are two highly regarded projectors designed to meet the needs of both home entertainment and professional presentations. Renowned for their advanced features and reliable performance, these models stand out in the competitive projector market.

The BenQ MX615 features a native XGA resolution (1024 x 768) which ensures crystal-clear image quality, making it an ideal choice for business meetings and classroom settings. It boasts a brightness of 3000 ANSI lumens, enabling it to perform well in various lighting conditions, from dimly lit rooms to brighter environments. The MX615 also has a high contrast ratio of 13,000:1, which enhances the depth and sharpness of images, ensuring that text and graphics are easily readable.

On the other hand, the BenQ MS614 offers a similar native SVGA resolution (800 x 600), making it an affordable option for those seeking a reliable projector for fundamental applications. With a brightness of 3300 ANSI lumens, the MS614 also excels in well-lit settings, providing vibrant colors and clear images. Its contrast ratio of 15,000:1 adds further clarity and richness to presentations, ensuring that every detail stands out.

Both projectors utilize DLP technology, known for its durability and low maintenance requirements. DLP projectors are less susceptible to color decay over time, ensuring consistent image quality. Additionally, they come equipped with BenQ's SmartEco technology, which intelligently adjusts the lamp power to optimize brightness based on content. This not only prolongs the life of the lamp but also reduces energy consumption, leading to cost savings.

The connectivity options are also noteworthy. The MX615 and MS614 support HDMI, VGA, and USB connections, making it easy to link to a variety of devices such as laptops, DVD players, and gaming consoles. This versatility ensures that users can easily switch between different sources without the need for additional adapters.

In summary, the BenQ MX615 and MS614 projectors offer a combination of excellent brightness, solid image quality, and advanced DLP technology. With a focus on performance and convenience, these projectors are suitable options for both professional and educational environments, providing a seamless presentation experience. Whether users prioritize higher resolution or affordability, BenQ has tailored these models to meet diverse needs with effectiveness and efficiency.