BenQ MS614, MX615 user manual Use the handle to slowly pull the lamp out Projector

Page 57

7.Use the handle to slowly pull the lamp out of

the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

•Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

8. As shown in the figure, lower the new lamp.

9.

Tighten the screw that secures the lamp.

 

10.

Ensure the handle is fully laid flat and locked

2

 

in place.

 

• Loose screw may cause a bad connection, which could result in malfunction.

1

• Do not over tighten the screw.

11.Replace the new protection film that comes

with the new lamp.

2

12. Replace the lamp cover on the projector.

2

 

1

13.Tighten the screw that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

Maintenance 57

Page 56 Page 58
Image 57
Page 56 Page 58
Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Front/upper side Projector exterior viewProjector Controls and functionsTimer On Volume +Timer Set up FreezeReplacing the remote control battery Remote control effective rangePull out the battery holder Ppr 15ºChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal VerticalConnection Connecting audio Connecting video source devicesTerminal name Terminal appearance BestOperation Starting up the projectorOperation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityTo correct keystoning at the bottom of the image Correcting keystoneUsing the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter the old password Enter a new passwordChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management To cancel the timer, perform the following steps Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-RightRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageLocking control keys To activate the High Altitude ModeOperating in a high altitude environment Creating your own startup screenAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a LAN environment Wireless connectionPage Page Page Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu system Menu operationMain menu Sub-menu Options BasicAdvanced Settings Monitor Out On/Off Closed Caption On/Off Enable Caption VersionWireless LAN Standby Network On/OffDescription of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function Description TeachingTimer System Setup Basic menu Function Description Quick AutoSettings SearchBackground Panel KeyLock SplashWireless System Setup Advanced menu Function DescriptionReset All Baud RateCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampLamp cover loosens Remove the lamp cover from Projector.1 Replacing the lampUse the handle to slowly pull the lamp out Projector Connect the power and restart the projector Resetting the lamp timerTime will be reset to Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmSupported timing for PC input Timing chart1360 x Supported timing for Hdmi Hdcp inputSupported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming Limited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive

MS614, MX615 specifications

The BenQ MX615 and MS614 are two highly regarded projectors designed to meet the needs of both home entertainment and professional presentations. Renowned for their advanced features and reliable performance, these models stand out in the competitive projector market.

The BenQ MX615 features a native XGA resolution (1024 x 768) which ensures crystal-clear image quality, making it an ideal choice for business meetings and classroom settings. It boasts a brightness of 3000 ANSI lumens, enabling it to perform well in various lighting conditions, from dimly lit rooms to brighter environments. The MX615 also has a high contrast ratio of 13,000:1, which enhances the depth and sharpness of images, ensuring that text and graphics are easily readable.

On the other hand, the BenQ MS614 offers a similar native SVGA resolution (800 x 600), making it an affordable option for those seeking a reliable projector for fundamental applications. With a brightness of 3300 ANSI lumens, the MS614 also excels in well-lit settings, providing vibrant colors and clear images. Its contrast ratio of 15,000:1 adds further clarity and richness to presentations, ensuring that every detail stands out.

Both projectors utilize DLP technology, known for its durability and low maintenance requirements. DLP projectors are less susceptible to color decay over time, ensuring consistent image quality. Additionally, they come equipped with BenQ's SmartEco technology, which intelligently adjusts the lamp power to optimize brightness based on content. This not only prolongs the life of the lamp but also reduces energy consumption, leading to cost savings.

The connectivity options are also noteworthy. The MX615 and MS614 support HDMI, VGA, and USB connections, making it easy to link to a variety of devices such as laptops, DVD players, and gaming consoles. This versatility ensures that users can easily switch between different sources without the need for additional adapters.

In summary, the BenQ MX615 and MS614 projectors offer a combination of excellent brightness, solid image quality, and advanced DLP technology. With a focus on performance and convenience, these projectors are suitable options for both professional and educational environments, providing a seamless presentation experience. Whether users prioritize higher resolution or affordability, BenQ has tailored these models to meet diverse needs with effectiveness and efficiency.
Top Page Image Contents