BenQ MS614, MX615 user manual Timing of replacing the lamp, Status Message

Page 55

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com for a replacement lamp.

The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator still lights up after turning the power back on, please contact your dealer. See "Indicators" on page 59 for details.

The following Lamp warning displays will remind you to change the lamp.

Status

Message

Install a new lamp for optimal performance. If the

Notice

projector is normally run with Economic selected

 

(See "Getting to know the lamp hour" on page 54),

Order Replacement Lamp

you may continue to operate the projector until

Lamp>XXXX Hours

the next hour lamp warning appears.

 

Press MODE/ENTER to dismiss the message.

Order a new lamp at lamp.benq.com

 

 

OK

 

 

It is strongly recommended that you replace the

Notice

lamp at this age. The lamp is a consumable item.

 

The lamp brightness diminishes with use. This is

Order Replacement Lamp

normal lamp behavior. You can replace the lamp

Lamp>XXXX Hours

whenever you notice that the brightness level has

 

significantly diminished.

Order a new lamp at lamp.benq.com

Press MODE/ENTER to dismiss the message.

OK

 

 

The lamp MUST be replaced before the projector

WARNING

will operate normally.

Out of Lamp Usage Time

Press MODE/ENTER to dismiss the message.

 

 

Replace lamp (refer to User Manual)

 

Then reset lamp timer

 

Order a new lamp at lamp.benq.com

 

OK

 

 

"XXXX" shown in the above messages are numbers that vary depending on different models.

Maintenance 55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedIntroduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewProjector Controls and functionsFreeze Volume +Timer On Timer Set upPpr 15º Remote control effective rangeReplacing the remote control battery Pull out the battery holderFront Ceiling Positioning your projectorChoosing a location Front TableVertical Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm DiagonalConnection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationOperation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageTo correct keystoning at the bottom of the image Correcting keystoneFollowing example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Enter a new password Changing the passwordDisabling the password function Enter the old passwordChanging Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageCreating your own startup screen To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneControlling the projector through a LAN environment Wireless connectionPage Page Page Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Basic Menu operationMenu system Main menu Sub-menu OptionsAdvanced Standby Network On/Off Closed Caption On/Off Enable Caption VersionSettings Monitor Out On/Off Wireless LANDescription of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsSplash Panel KeyBackground LockBaud Rate System Setup Advanced menu Function DescriptionWireless Reset AllStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampLamp cover loosens Remove the lamp cover from Projector.1 Replacing the lampUse the handle to slowly pull the lamp out Projector Resetting the lamp timer Connect the power and restart the projectorTime will be reset to Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsUnit mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Ceiling Mount screw M4 x 8 Max L = 8 mmSupported timing for PC input Timing chart1360 x Supported timing for Hdmi Hdcp inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users

MS614, MX615 specifications

The BenQ MX615 and MS614 are two highly regarded projectors designed to meet the needs of both home entertainment and professional presentations. Renowned for their advanced features and reliable performance, these models stand out in the competitive projector market.

The BenQ MX615 features a native XGA resolution (1024 x 768) which ensures crystal-clear image quality, making it an ideal choice for business meetings and classroom settings. It boasts a brightness of 3000 ANSI lumens, enabling it to perform well in various lighting conditions, from dimly lit rooms to brighter environments. The MX615 also has a high contrast ratio of 13,000:1, which enhances the depth and sharpness of images, ensuring that text and graphics are easily readable.

On the other hand, the BenQ MS614 offers a similar native SVGA resolution (800 x 600), making it an affordable option for those seeking a reliable projector for fundamental applications. With a brightness of 3300 ANSI lumens, the MS614 also excels in well-lit settings, providing vibrant colors and clear images. Its contrast ratio of 15,000:1 adds further clarity and richness to presentations, ensuring that every detail stands out.

Both projectors utilize DLP technology, known for its durability and low maintenance requirements. DLP projectors are less susceptible to color decay over time, ensuring consistent image quality. Additionally, they come equipped with BenQ's SmartEco technology, which intelligently adjusts the lamp power to optimize brightness based on content. This not only prolongs the life of the lamp but also reduces energy consumption, leading to cost savings.

The connectivity options are also noteworthy. The MX615 and MS614 support HDMI, VGA, and USB connections, making it easy to link to a variety of devices such as laptops, DVD players, and gaming consoles. This versatility ensures that users can easily switch between different sources without the need for additional adapters.

In summary, the BenQ MX615 and MS614 projectors offer a combination of excellent brightness, solid image quality, and advanced DLP technology. With a focus on performance and convenience, these projectors are suitable options for both professional and educational environments, providing a seamless presentation experience. Whether users prioritize higher resolution or affordability, BenQ has tailored these models to meet diverse needs with effectiveness and efficiency.
Top Page Image Contents