BenQ MW512 Operating in a high altitude environment, Adjusting the sound, Muting the sound

Page 41

Operating in a high altitude environment

We recommend you use the High Altitude Mode when your environment is between 1500 m –3000 m above sea level, and ambient temperature is between 0°C–35°C.

Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under such a condition.

To activate the High Altitude Mode:

1.Press Menu/Exit and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight High Altitude Mode and press / to select On. A confirmation message displays.

3.Highlight Yes and press Mode/Enter.

Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.

If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to High Altitude mode to solve these symptoms.

However, this is not to state that this projector can operate under any and all harsh or extreme conditions.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker(s). Be sure you have made a correct connection to the projector audio input. See "Connection" on page 18 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.Press Menu/Exit and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight Audio Settings and press Mode/Enter. The Audio Settings page displays.

3.Highlight Mute and press / to select On.

Adjusting the sound level

To adjust the sound level, press Volume +/- on the remote control, or:

1. Repeat steps 1-2 above.

2. Press to highlight Volume and press / to select a desired sound level.

Operation 41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents MW512 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection Connecting a computer Connecting a computer or monitorConnecting a monitor To connect the projector to a notebook or desktop computerConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Operation Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorPress Mode/Enter and the 3D Color Management page displays About color temperatures3D Color Management Creating your own startup screen To cancel the timer, perform the following steps Setting the presentation timerPresentation Timer Top-Left Bottom-Left Top-Right Bottom-RightHiding the image How to use the Timer On key?Remote paging operations To highlight the Information menu Utilizing FAQ functionFreezing the image Adjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Invert 3D SyncTeaching TemplatePicture menu Picture ModeReference ModeSave Settings TemperatureInput signal Picture menu Source menuMenu Settings Presentation TimerOperation System Setup Basic menuRemote ReceiverQuick System Setup Advanced menuCooling High AltitudeClosed Reset AllCaption StandbyFeatures Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsCeiling mount installation DimensionsCeiling mount screws Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements

MW512 specifications

The BenQ MW512 is a versatile and feature-rich projector that caters to both educational and business environments. Designed to deliver high-quality images and user-friendly operation, the MW512 stands out as a reliable tool for presentations, lectures, and multimedia entertainment.

At the heart of the MW512 is its impressive resolution of 1280 x 800 pixels, which delivers crisp and vibrant images, ensuring that text is sharp and visuals are clear. This native WXGA resolution makes it an excellent choice for widescreen content, as it can easily accommodate 16:10 aspect ratios. With a brightness of 3200 ANSI lumens, the MW512 is equipped to perform well in various lighting conditions, from dimly lit rooms to more brightly illuminated spaces. This high brightness level ensures that presentations remain clear and impactful.

The BenQ MW512 employs advanced DLP technology, which enhances image quality through better color reproduction and enhanced contrast. The projector's 10,000:1 dynamic contrast ratio enables rich blacks and bright whites, creating a more dynamic viewing experience. Whether it's detailed graphics, charts, or videos, the MW512 showcases content with exceptional clarity.

Another notable feature of the MW512 is its extensive connectivity options. The projector is equipped with multiple input ports, including HDMI, VGA, and USB, enabling seamless integration with a variety of devices such as laptops, tablets, and DVD players. This flexibility makes it easy for users to switch between devices without the hassle of changing cables.

In addition to its technical prowess, the MW512 is designed with user convenience in mind. With a lightweight and compact design, transporting the projector is a breeze, making it ideal for those who require a mobile solution. Easy installation is facilitated by features such as vertical keystone correction, which helps to ensure that the projected image remains aligned regardless of projector placement.

Furthermore, the MW512 incorporates energy-efficient technologies, contributing to a longer lamp life of up to 10,000 hours. This not only reduces maintenance costs but also minimizes the environmental impact associated with frequent lamp replacements.

In summary, the BenQ MW512 is a powerful projector that combines exceptional image quality, versatility, and user-friendly features. Whether for business presentations, educational purposes, or home entertainment, the MW512 delivers a superior visual experience that is sure to impress.
Top Page Image Contents