BenQ MW512 user manual Maintenance, Care of the projector

Page 55

Maintenance

Care of the projector

Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens and case clean.

Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface.

•Use a canister of compressed air to remove dust.

•If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.

•Never use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the projector surface and cabinet material.

Never rub the lens with abrasive materials.

Cleaning the projector case

Before you clean the case, turn the projector off using the proper shutdown procedure as described in "Shutting down the projector" on page 42 and unplug the power cord.

•To remove dirt or dust, wipe the case with a soft, lint-free cloth.

•To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then wipe the case.

Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.

Storing the projector

If you need to store the projector for an extended time, please follow the instructions below:

•Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to "Specifications" on page 63 or consult your dealer about the range.

•Retract the adjuster feet.

•Remove the battery from the remote control.

•Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.

Maintenance 55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents MW512 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Up/Down Remote controlSetting the presentation timer on Timer On Timer SetupChoosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitorConnecting audio Connecting Video source devicesTo connect the projector to an Hdmi source device Connecting an Hdmi source deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite source deviceStarting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordChanging the password Entering the password recall procedureDisabling the password function Operation Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Using Wall Color3D Color Management About color temperaturesPress Mode/Enter and the 3D Color Management page displays Creating your own startup screen Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Presentation TimerRemote paging operations How to use the Timer On key?Hiding the image Freezing the image Utilizing FAQ functionTo highlight the Information menu Operating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude ModeShutting down the projector Personalizing the projector menu displayMenu system Menu operationSystem Setup Basic Advanced SetupDescription of each menu Template 3D SyncInvert TeachingMode Picture ModePicture menu ReferencePicture menu Source menu TemperatureSave Settings Input signalMenu Settings Presentation TimerReceiver System Setup Basic menuOperation RemoteHigh Altitude System Setup Advanced menuQuick CoolingStandby Reset AllClosed CaptionCurrent FAQ-Image InstallationFeatures Service Information menuCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Projector and b lifting it off Tighten the screws that secure the lamp Resetting the lamp timerPower Temp Lamp IndicatorsTroubleshooting Optical SpecificationsUnit mm DimensionsCeiling mount installation Ceiling mount screwsSupported timing for PC input Timing chartSupported timing for Hdmi input Supported timing for Component-YPbPrinput Limited warranty Warranty and Copyright informationFCC statement Regulation statementsRegulation statements

MW512 specifications

The BenQ MW512 is a versatile and feature-rich projector that caters to both educational and business environments. Designed to deliver high-quality images and user-friendly operation, the MW512 stands out as a reliable tool for presentations, lectures, and multimedia entertainment.

At the heart of the MW512 is its impressive resolution of 1280 x 800 pixels, which delivers crisp and vibrant images, ensuring that text is sharp and visuals are clear. This native WXGA resolution makes it an excellent choice for widescreen content, as it can easily accommodate 16:10 aspect ratios. With a brightness of 3200 ANSI lumens, the MW512 is equipped to perform well in various lighting conditions, from dimly lit rooms to more brightly illuminated spaces. This high brightness level ensures that presentations remain clear and impactful.

The BenQ MW512 employs advanced DLP technology, which enhances image quality through better color reproduction and enhanced contrast. The projector's 10,000:1 dynamic contrast ratio enables rich blacks and bright whites, creating a more dynamic viewing experience. Whether it's detailed graphics, charts, or videos, the MW512 showcases content with exceptional clarity.

Another notable feature of the MW512 is its extensive connectivity options. The projector is equipped with multiple input ports, including HDMI, VGA, and USB, enabling seamless integration with a variety of devices such as laptops, tablets, and DVD players. This flexibility makes it easy for users to switch between devices without the hassle of changing cables.

In addition to its technical prowess, the MW512 is designed with user convenience in mind. With a lightweight and compact design, transporting the projector is a breeze, making it ideal for those who require a mobile solution. Easy installation is facilitated by features such as vertical keystone correction, which helps to ensure that the projected image remains aligned regardless of projector placement.

Furthermore, the MW512 incorporates energy-efficient technologies, contributing to a longer lamp life of up to 10,000 hours. This not only reduces maintenance costs but also minimizes the environmental impact associated with frequent lamp replacements.

In summary, the BenQ MW512 is a powerful projector that combines exceptional image quality, versatility, and user-friendly features. Whether for business presentations, educational purposes, or home entertainment, the MW512 delivers a superior visual experience that is sure to impress.
Top Page Image Contents