Ampro Corporation 486E manual Ethernet LAN Interface, Byte-Wide Socket and Solid State Disk SSD

Page 12

Little Board™/486e Technical Manual

Ethernet LAN Interface

The Ethernet LAN interface uses Carrier Sense, Multiple Access/Collision Detect (CSMA/CD) for node access and operates at a 10M-bits/second data rate. The Ethernet interface has the following features:

!Contains the logic necessary to send and receive data packets

!Controls CSMA/CD network access technology

!Meets IEEE 802.3 (ANSI 8802-3) Ethernet standards

!Supports the Ethernet twisted-pair standard (10BaseT)

Because Ethernet is preferred in many applications due to its high data rate and broad level of compatibility, Ampro supplies the Little Board/486e CPU with drivers and utilities to ensure compatibility with a wide range of popular operating systems and network operating systems. The Ethernet interface is based on the SMC9000-series single-chip Ethernet controller. DOS software drivers for ODI, NDIS, packet, and TCP/IP are supplied with the Little Board/486e Development Kit. OS support includes QNX, UNIX, Windows®9x, Windows NT, Windows CE and DOS.

The Ethernet interface provides boot PROM capability. When implemented, the embedded system boots directly from the network, eliminating the need for a local floppy, hard drive, or SSD.

Byte-Wide Socket and Solid State Disk (SSD)

The byte-wide memory socket included with the Little Board/486e CPU allows you to install a bootable “solid state disk” (SSD) for installation of embedded application software. The SSD supports:

!EPROM

!FLASH EPROM

!Battery-backed SRAMs

Using Ampro’s SSD Support Software, any DOS-based application, including the operating system, utilities, drivers, and application programs, can be run from SSD without modification. SSD operation is also supported by a number of real-time operating systems.

The board’s 32-pin byte-wide socket accepts 32-pin byte-wide memory devices. It accommodates

128K bytes to 1M byte devices and supports:

!CMOS SRAM

!SRAM non-volatile modules

!EPROM

!FLASH EPROM

1–4

Image 12
Contents Little Board/486e Computer Revision Reason for Change Date Table of Contents Page Technical Specifications Index Introduction Technical SupportThis page left intentionally blank Viii Features ChapterGeneral Description CPU/MotherboardEnhanced Embedded-PC Bios VL-Bus Flat Panel/CRT Display ControllerSerial Ports Enhanced Parallel PortFloppy Interface IDE InterfaceEthernet LAN Interface Byte-Wide Socket and Solid State Disk SSDEnhanced Reliability Modular PC/104 Expansion BusHalt Testing Software Little Board Development Platform Interface Connector Summary OverviewConnector Function Size Key Pin ConnectorsConnector and Jumper Locations Jumper Configuration Options Jumper Group Function DefaultSystem I/O Map Address Function DC Power Connector Type Mating ConnectorPin Connection Power Requirements Backup BatteryCooling Requirements Powerfail Monitor Dram System Memory MapExpanded Memory and Extended Memory Memory Address FunctionSerial Ports J11, J13 RS-232C Serial PortsRS-485 Serial Port AddressesInterrupt Assignments IRQ11 IRQ7ROM-BIOS Installation of the Serial Ports Serial Port Connectors J11, J13Ports Pin Signal Function In/Out DB25 Name PinConfiguring Serial 2 for RS-485 J6, W5, W6 Pin Signal NameRS-485 Twisted-Pair Cabling Using RJ11 Connectors Pin RJ11 Signal Standard Wire ColorUsing the RS-485 Interface Interconnection Scheme ExamplesHex Command Serial ConsoleCOM Port Table Serial HandshakeSerial Booting and Serial Programming Using a Serial ModemBi-Directional Parallel Port Register Name Address Primary SecondarySelection Address Interrupts ROM-BIOS Installation of Parallel Ports Signal Type Number of Lines Function Output DriveStandard and General Purpose I/O Operation Parallel Port Interrupt Parallel Port Interrupt Enable Register Bit Signal Name In/Out Active J15Or Function High/Low Pin Parallel Port Connector J15 J15 Pin Signal Function In/Out DB25 NameSignal Name Full Name Description Register Bit DefinitionsFloppy Disk Interface Floppy Drive ConsiderationsCapacity Drive Size Tracks Data Rate Floppy Interface Configuration Floppy Interface Connector J14Pin Signal Name Function In/Out IDE Connector J12 IDE Hard Disk Interface25. IDE Drive Interface Connector J12 IDE Interface Configuration Master/Slave Setting Compact Flash Solid-State DiskEnabling the Drive Solid-State Disk PreparationConnecting a CRT J5 Name Connector Pins/Type DescriptionFlat Panel/CRT Video Controller J5 Pin Signal Name DB-15 DB-9 Part Description Mating ConnectorConnecting a Flat Panel J3 W10 +5VPin Signal Description Name FLMPower Sequencing Advanced Power ManagementBios Support of Non-Standard Panels Pgmebios VIDEO=filenameSelecting Vee Polarity LCD Bias Supply OptionJ4 Pin J3 Pin Description Attaching an External Contrast Control Ra = 270 Rb = Vee max Vee min / 1.5Example Ethernet Network Interface Network TermsInstalling an Ethernet Boot Prom QNXTwisted-Pair Installations Installing a Boot PromInstalling a Boot Prom in Byte-Wide Socket S0 Twisted Pair Interface J7Using Network Operating Systems NOS Network OS Drivers Controlling the Ethernet LAN Interface DirectlyProgram Name Vendor Function Driver Name Manufacturer’s Ethernet ID 00 40SSD Device Size Package Generic Type Pins Part Number Byte-Wide Socket S0ROM-BIOS Extensions Addressing the Byte-wide SocketWindow Address Accessing the Byte-Wide Socket Performance IssuesSolid State Disk SSD Drives Device 64KB Segment Address Size Segments Upper Nibble of BH Byte-Wide Socket Signals Typical Devices Pins Jumper DiagramW14 Pin Signal Name Description Jumpering the Byte-Wide SocketUsing EPROMs Flash Eprom Typical Devices Pins Jumper DiagramFlash Eprom Programming Using SRAMs Non-volatile RAMUtility Connector J16 Pin Signal Name Function ExsmiPush Button Reset Connection External Battery ConnectionsPC Speaker LED ConnectionBattery-Backed Clock Watchdog Timer Jumper W4WDT Response AL,61H AL,NOT 08H OUT 61H,AL Page AT Expansion Bus Using Standard PC and AT Bus Cards Onboard MiniModule ExpansionBus Expansion Guidelines Bus TerminationExpansion Bus Connector Pinouts Pin Signal Function In/Out Current PU/PD/S47. AT Expansion Bus Connector, B1-B32 P1 48. AT Expansion Bus Connector, C0-C19 P2 PU/PD/S Interrupt and DMA Channel Usage Interrupt FunctionChannel Function Serial Parallel FloppyEthernet Video Setup Overview Menu Name Functions Setup Page 1-Standard CMOS/EEPROM Setup Standard CMOS/EEPROM SetupDrive Parameter Setup Date and TimeFloppy Drives IDE Hard Disk DrivesPage Error Halt VideoDram Memory System PostSetup Page 2-Options/Peripheral Configuration Extended BiosSerial Port Parallel PortPort Address Selection Address InterruptFloppy Interface Enable IDE Interface EnableHot Key Setup Enable Selection AddressVideo State Blank Post TestByte-Wide Socket Configuration Serial Boot Loader EnableWatchdog Timer Configuration Local Bus Video DisplayInstalling a Modified Bios to Support a New Panel Flat Panel Display TypeSetup Page 3-Serial Console Configuration Extended Serial Console ConfigurationPage Creating Configuration Files with SETUP.COM Switch FunctionOperation with DOS DIR LPT1Utility Software Overview Little Board/486e CPU Specifications Embedded-PC System EnhancementsOnboard Peripherals CRT Support for Standard Video Modes Vesa Font Pixels Clock Horiz Vert Mem Mode MHz KHz Support Software Mechanical and Environmental Specifications Mechanical Dimensions Technical Specifications Page Index Page POST, Setup Little Board/486e Technical Manual Index-4