Onkyo TX-SA705 instruction manual 113

Troubleshooting—Continued

Can’t control other components

•If it’s an Onkyo component, make sure that the cable and analog audio cable are connected properly.

Connecting only an cable won’t work (page 43).

•Make sure you’ve selected the correct remote control- ler mode (pages 15-19).

•If you’ve connected an -capable Onkyo MD

recorder, CD recorder, Dock to the TAPE IN/

OUT jacks, or an Dock to the GAME/TV IN jacks, for the remote controller to work properly, you must set the display to MD, CDR, or DOCK (page 50).

When operating a DS-A1 RI Dock, enter the appropri- ate remote control code for the first time (page 104).

•To control another manufacturer’s component, point the remote controller at that component.

•To control an Onkyo component that’s connected via

, point the remote controller at the AV receiver/AV amplifier. Be sure to enter the appropriate remote con- trol code first (page 105).

•To control an Onkyo component that’s not connected

via , or another manufacturer’s component, point the remote controller at the component. Be sure to enter the appropriate remote control code first (page 104).

Recording

Can’t record

•On your recorder, make sure the correct input is selected (e.g., digital or analog).

•When the Pure Audio listening mode is selected, record- ing is not possible because no video signals are output. Select another listening mode.

Zone 2

There’s no sound

•Only components connected to analog inputs can be played in Zone 2.

Others

The sound changes when I connect my head- phones

•When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono, Direct, or Pure Audio.

The speaker volume cannot be set as required

•When the Automatic Speaker Setup function is used, or the volume is adjusted on the onscreen setup menus, the maximum possible volume setting may change.

The speaker distance cannot be set as required

•In some cases, corrected values suitable for home the- ater use may be set automatically.

The display doesn’t work

•The display is turned off when the Pure Audio (not North American models) listening mode is selected.

How do I change the language of a multiplex source

•Use the “Multiplex” setting on the “Audio Adjust” menu to select Main or Sub (page 85).

The functions don’t work

•To use , you must make an connection and an analog audio connection (RCA) between the compo- nent and AV receiver/AV amplifier, even if they are connected digitally (page 43).

The functions Auto Power On/Standby and Direct Change don’t work for components con- nected via

• These functions don’t work when Zone 2 is turned on.

When performing “Automatic Speaker Setup,” the measurement fails showing the message “Ambient noise is too high.”

•This can be caused by any malfunction in your speaker unit. Check if the unit produces normal sounds.

The following settings can be made for the S-Video and composite video inputs

You must use the buttons on the unit to make these set- tings.

1.While holding down the input selector button for the input source that you want to set, press the [SETUP] button.

2.	Use the Left and Right [ ]/[ ] buttons to change
	the setting.
3.	Press the [SETUP] button when you’ve finished.

• Video Attenuation

This setting can be made for the DVD, VCR/DVR, CBL/SAT, GAME/TV, or AUX input.

If you have a games console connected to the S-Video or composite video input, and the picture isn’t very clear, you can attenuate the gain.

Video ATT:0: (default).

Video ATT:2: Gain is reduced by 2 dB.

The AV receiver/AV amplifier contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded cor- rectly.

Before disconnecting the power cord from the wall out- let, set the AV receiver/AV amplifier to Standby.

113