Onkyo TX-SA705 instruction manual Speaker Connection Precautions, Connecting the Speaker Cables

Page 23

Connecting the AV Receiver/AV Amplifier—Continued

Speaker Connection Precautions

Read the following before connecting your speakers:

•North American models: Only connect speakers with an impedance of 6 ohms or higher. If you use speakers with a lower impedance, and use the ampli- fier at high volume levels for a long period of time, the built-in protection circuit may be activated.

•Other models: You can connect speakers with an impedance of between 4 and 16 ohms. If the imped- ance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to “4 ohms” (see page 46). If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in protection circuit may be activated.

•Disconnect the power cord from the wall outlet before making any connections.

•Read the instructions supplied with your speakers.

•Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive

(+) terminals, and negative (–) terminals only to nega- tive (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

•Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

•If you use 4 or 5 speakers, connect each of the two surround speakers to the SURR SPEAKERS termi- nals. Do not connect them to the SURR BACK SPEAKERS terminals.

•Be careful not to short the positive and negative wires.

Doing so may damage the AV receiver/AV amplifier.

• Make sure the metal core of the wire does not have contact with the AV receiver/AV amplifier’s rear panel. Doing so may dam- age the AV receiver/AV amplifier.

•Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver/AV amplifier.

•Don’t connect one speaker to several terminals.

Connecting the Speaker Cables

1

Strip about 5/8" (15 mm)

5/8" (15 mm)

 

of insulation from the

 

 

ends of the speaker

 

 

cables, and twist the bare

 

 

wires tightly, as shown.

 

2

Unscrew the terminal.

 

3

Fully insert the bare

 

 

wires.

 

4

Screw the terminal tight.

 

The following illustration shows which speaker should be connected to each pair of terminals.

If you’re using only one surround back speaker, connect it to the left (L) SURR BACK SPEAKERS terminals.

Surround Surround Surround Surround

back left back right left right

speaker speaker speaker speaker

Front right

Front left

Center

speaker

speaker

speaker

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents TX-SR705 Important Safety Instructions FCC Information for User PrecautionsPower For North American modelFor British models PrecautionsMake sure you have the following accessories Supplied AccessoriesConnections FeaturesAmplification ProcessingTable of Contents Front Panel Front & Rear PanelsFront & Rear Panels Display TX-SR705 other than North American model Rear PanelTX-SR705 North American model  XM antenna North American models only  Digital Optical in 1, 2 and OUT Digital Coaxial in 1, 2  Sirius antenna North American models onlyAC Outlet North American and European models only SUBWOOFER, Surr L/R, and Surr Back L/RAiming the Remote Controller Remote ControllerInstalling the Batteries RECEIVER/TAPE Mode Remote ControllerUsing the Remote Controller  on button Remote Mode buttonsTape mode  Standby buttonDVD Mode OPEN/CLOSE button CD/MD/CDR ModesDock Mode Enjoying Home Theater About Home TheaterAV Connection Color Coding Connecting the AV Receiver/AV AmplifierAbout AV Connections Optical Digital JacksConnecting Your Speakers Connecting the AV Receiver/AV AmplifierStrip about 5/8 15 mm Speaker Connection PrecautionsConnecting the Speaker Cables Read the following before connecting your speakersBi-amping Speaker Hookup Bi-amping the Front SpeakersAttach the FM antenna, as shown North American models Connecting Antenna TX-SR705 onlyConnecting the Indoor FM Antenna Connecting the AM Loop AntennaUsing a TV/FM Antenna Splitter Connecting an Outdoor FM AntennaConnecting an Outdoor AM Antenna Video Connection Formats Connecting Both Audio & VideoHdmi Monitor Setting Set to Yes Which Connections Should I Use?Audio Connection Formats Hdmi Monitor Setting Set to NoHint Connecting a TV or ProjectorVideo Connection Audio ConnectionConnecting a DVD Player Hooking Up the Multichannel DVD Input Connecting a VCR or DVD Recorder for Playback Connecting a VCR or DVD Recorder for Recording Satellite, cable, set-top box, etc Connecting a Game Console Camcorder, etc Connecting a Camcorder or Other DeviceAbout Copyright Protection Connecting Components with HdmiAbout Hdmi Supported Audio FormatsMaking Hdmi Connections Video SignalsAudio Signals Turntable MM with no Phono Preamp Built-in Connecting a CD Player or TurntableCD Player or Turntable MM with Built-in Phono Preamp Step Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Connecting a Tuner TX-SA705 only Connecting a Power AmplifierIf you have an Onkyo DS-A1 RI Dock Connecting an RI DockIPod with video IPod without videoConnecting the Power Cord Connecting Onkyo ComponentsConnecting the RS232 Port Smooth Operation in a Few Easy Steps Turning On the AV Receiver/AV AmplifierTurning On and Standby Press the Receiver button fol- lowed by the Setup button First Time SetupUsing the Onscreen Setup Menus Menus for First Time SetupSpeaker Setup menu appears First Time SetupSpeaker Settings Press the Receiver button, followed by the Setup buttonMonitor Out menu appears Hdmi Monitor SetupSetup menu closes Input/Output Assign menu appearsHdmi Input menu appears Video Input SetupHdmi Input Setup 2 Use the video component connected to Compo Component Video SetupComponent Video Input menu appears 1 Use the video component connected to CompoTape o MD o CDR o Dock Changing the Input DisplayChanges in this order Digital Input Setup You must specify the TV system used in your area TV Format Setup Not North American modelsWhen you’ve finished, press the Setup button OSD Setup menu appearsUse the Left and Right AM Frequency Step Setup on some modelsHardware Setup menu appears Measurement Positions Automatic Speaker Setup Audyssey MultEQ XTUsing Audyssey MultEQ XT Next CancelPress Enter Speaker detect results appearMicrophone Disconnect the speaker setupButtons to select an option, Then press EnterAmbient noise is too high Error MessagesSpeaker Detect Error Writing ErrorReviewing the Results Changing the Speaker Settings ManuallyUsing a Powered Subwoofer Selecting the Input Source Select a listening mode and enjoySee Using the Listening Modes on Basic OperationsBasic Operations Using the Multichannel DVD InputAdjusting the Bass & Treble Multi CH indicator appears on the displayMuting the AV receiver/AV amplifier Setting the Display BrightnessUsing the Sleep Timer Using HeadphonesListening to the Radio Using the TunerTuning into Radio Stations Listening to the Radio TX-SR705 onlySelect the preset that you want to delete Presetting AM/FM StationsSelecting Presets Deleting PresetsRDS Program Types PTY Using RDS European models onlyWhat is RDS? Listening to Traffic News TP Displaying Radio Text RTFinding Stations by Type PTY Selecting on the AV receiver/AV amplifier Using the Listening ModesSelecting with the Remote Controller Selecting Listening ModesAnalog and PCM Sources Using the Listening ModesListening Modes Available for Each Source Format Sacd DSD, Dolby Digital, and Dolby Digital Plus SourcesDTS-ES TrueHD and DTS SourcesDTS-HD Sources About the Listening Modes Use this mode with any stereo movie e.g., TV, DVD, VHSDSD Onkyo Original DSP Modes Theater-DimensionalRecording Separate AV Sources RecordingAV Recording Dolby Digital, Dolby Digital Plus Using the Re-EQ FunctionAdjusting Individual Speaker Levels Advanced OperationsAbout the Onscreen Setup Menus Advanced SetupButtons to select Subwoofer Advanced SetupSpeaker Setup Speaker SettingsIf no surround back speakers are con- nected, select None Low-Pass Filter for the LFE ChannelFrequency Use the Up and Down / buttons to select LPF of LFEDouble Bass Setup menu closesUse the Left and Right Buttons to specify the distance Repeat for all speakers Press the Setup buttonSpeaker Distance Because the test tone will be much louder Mally listen at volume settings below this, be carefulSpeaker Level Calibration Enter Equalizer SettingSpeaker THX Audio SetupButtons to select 2. Speaker Setup, and then press Enter Buttons to select anotherFt 0.3-1.2 m Select this if your Multichannel DVD Input SettingsButtons to select 7. Hardware Setup, and then press Enter Subwoofer Input SensitivityMultiplex/Mono Settings Audio Adjust FunctionsTone Control Settings LFE Level Settings PLIIx/Neo6 Music Mode SettingsDolby EX Input Signal Setting Theater-Dimensional Listening SettingAssigning Listening Modes to Input Sources Listening Mode Preset menu appearsSignal format selection menu appears Level can be set from -12 dB to +12 dB in 1 dB steps Source SetupSource Setup menu appears When you’re finished, press the Setup buttonPress Enter to view the TV picture, and use the Left Right / buttons to adjustDelay from 0 to 250 millisec A/V Sync menu appearsName Edit screen appears Name EditTo correct a character 123456789 This section explains the items on the Miscellaneous menu Volume Setup/OSD SetupVolume Setup Volume Setup menu appearsSee TV Format Setup not North American models on OSD SetupChanging the AV Receiver/AV Amplifier’s ID XvYCC Hdmi SetupHdmi Audio Out Lip SyncTV Control Power ControlControl Buttons to select 8. Lock Setup, and then press Enter Lock SetupDigital Input Signal Formats Off, try setting the format to PCMUse the number buttons to enter ID 1, 2, or Changing the Remote Controller’s IDRemote indicator flashes four times Remote indicator flashes twiceZone Connecting ZoneUsing a Receiver/Integrated Amp in Zone Using Only Speakers in Zone100 Setting the Powered ZoneControlling Zone 2 from the AV receiver/AV amplifier Using ZoneControlling Zone 2 with the Remote Controller 101To Mute Zone Adjusting the Volume for Zone102 103 Using a Multiroom Kit with ZoneUsing a Multiroom Kit with a Cabinet 104 Entering Remote Control CodesRemote indicator lights up Controlling Other Components105 Remote Control Codes for Onkyo Components Connected viaResetting Remote Mode Buttons Resetting the Remote Controller106 107 Learning CommandsRunning Macros Using Macros108 Making Macros109 Specifications110 Troubleshooting111 Troubleshooting112 113 114 Memo115 3 4 4 4 7 6 a

TX-SA705 specifications

The Onkyo TX-SA705 is a versatile AV receiver designed for audiophiles seeking an immersive home theater experience. Combining advanced technology with user-friendly features, this receiver is well-suited for both casual listeners and serious home theater enthusiasts.

One of the standout characteristics of the TX-SA705 is its impressive power output. Delivering 100 watts per channel across seven channels, it ensures that audio plays back with clarity and authority, providing enough power to fill large rooms with rich sound. The receiver supports a range of surround sound formats, including Dolby Atmos and DTS:X, allowing users to experience cinema-quality audio at home. These technologies create a three-dimensional sound environment, immersing listeners in the action.

Connectivity is another key feature of the TX-SA705. The receiver is equipped with multiple HDMI inputs, supporting 4K video passthrough and HDR for stunning visuals. With ARC (Audio Return Channel) capability, the TX-SA705 simplifies the connection to compatible televisions, allowing for easy audio output. The inclusion of Bluetooth technology enables wireless streaming from smartphones and tablets, making it more convenient to enjoy music from various sources.

The Onkyo TX-SA705 also boasts an intuitive user interface designed for ease of use. The graphical user interface helps users navigate settings and options seamlessly, while the included remote control features direct access buttons for the most commonly used functions. Furthermore, the receiver is compatible with Onkyo's Controller app, providing additional control through smartphones.

In terms of sound customization, the TX-SA705 stands out with its advanced equalization features. The receiver incorporates Audyssey technology, which automatically calibrates audio settings based on room acoustics. This ensures optimal sound performance tailored to the specific environment.

Finally, the build quality of the TX-SA705 is noteworthy. Onkyo has designed this receiver with a sturdy chassis and high-quality components that enhance durability and performance. The TX-SA705 not only delivers impressive audio-visual performance but is also built to last, making it a wise investment for any home theater setup.

In summary, the Onkyo TX-SA705 combines powerful audio performance, modern connectivity options, and intelligent sound optimization features to create a receiver that meets the demands of contemporary home theater systems. Whether for movie nights or music playback, the TX-SA705 is a fantastic choice for an immersive entertainment experience.
Top Page Image Contents