LG Electronics 22EN33S, 23EN33S, 20EN33SS, 19EN33SW owner manual Mounting on a wall, 24EN33S

Page 9

8ASSEMBLING AND PREPARING

ENGLISH

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.

10 cm

10 cm

10 cm

10 cm

If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.

When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.

1Please, Use the screw and wall mount interface in accordance with VESA Standards.

2If you use screw longer than standard, the monitor might be damaged internally.

3If you use improper screw, the product might be damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.

4VESA compatible.

5Please use VESA standard as below.

yy784.8 mm (30.9 inch) and under

*Wall Mount Pad Thickness : 2.6 mm

* Screw : Φ 4.0 mm x Pitch 0.7 mm x

Length 10 mm

yy787.4 mm (31.0 inch) and above

*Please use VESA standard wall mount pad and screws.

Model

19EN33S 20EN33S

 

19EN33SW 22EN33S

 

20EN33SS 23EN33S

VESA (A x B)

75 x 75

Standard screw

M4

Number of screws

4

Model

24EN33S

VESA (A x B)

100 x 100

Standard screw

M4

Number of screws

4

CAUTION

yyDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.

yyIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury.

yyUse only an authorized LG wall mount and contact the local dealer or qualified personnel.

yyDo not over tighten the screws as this may cause damage to the Monitor set and void your warranty.

yyUse only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.

NOTE

yyUse the screws that are listed on the VESA standard screw specifications.

yyThe wall mount kit will include an installation manual and necessary parts.

yyThe wall mount bracket is optional. You can obtain additional accessories from your local dealer.

yyThe length of screws may differ depending on the wall mount. Be sure to use the proper length.

yyFor more information, refer to the instructions supplied with the wall mount.

Image 9
Contents LED LCD Monitor Page Contents Assembling and Preparing Card Power Cord AC-DC AdapterUnpacking SUB CableParts and buttons Attaching the Stand Base Setting up the Monitor setDetaching the Stand Base Pull out the Stand Body and Stand Base from the monitor setUsing the cable holder Mounting on a tableCable holder Front Rear 24EN33S Mounting on a wallConnecting to a PC Using the Monitor SETSUB connection YyMac adapterYy‘AUTO’ Function YySelf Image Setting FunctionMonitor set Buttons Customizing SettingsMenu Settings Customizing SettingsPicture Color Display Others MY KEY MY KEY SettingPicture Mode FUNC. SettingSuper Energy Saving Dual Display MY KEY Setting Check the following before calling for service TroubleshootingRecommend resolution Settings19EN33S Specifications19EN33SW 20EN33SS ‌SPECIFICATIONS20EN33S SPECIFICATIONS‌Weight Tilt Range Environmental Operating Temperature 22EN33SDepth 23EN33S 24EN33S 19EN33S Preset Modes Resolution22EN33S/23EN33S/24EN33S IndicatorProper Posture Proper posture for using the Monitor setDeclaration of Conformity