LG Electronics MM22229944DD, MM22009944DD, MM11999944DD VCR Setup, When connecting with an antenna

Page 14

EXTERNAL EQUIPMENT SETUP

VCR SETUP

To avoid picture noise (interference), leave an adequate distance between the VCR and set.

Typically a still picture is shown on the VCR. If a user uses 4:3 picture format for a long time, an afterimage may remain on the sides of the screen.

When connecting with an antenna

ANTENNA IN

1

ANT OUT S-VIDEO VIDEO

L

R

ANT IN

OUTPUT

SWITCH

 

Wall Jack

2

Antenna

1Connect the RF out socket of the VCR to the aerial socket of the set.

2Connect the aerial cable to the RF aerial in socket of the VCR.

3Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.

4Select the programme number where the VCR channel is stored.

5 Press the PLAY button on the VCR.

13

Image 14
Contents ID Numbers 5573 M1994D 5574 M2094D 5575 M2294D Preparation Front Panel ControlsBack Panel Information Stand Installation Detaching Stand Desktop Pedestal Installation Positioning Your Display LocationKensington Security System Antenna Connection AntennaImage shown may be somewhat different from your set HD Receiver SetupWhen connecting with a component cable 480i/576iWhen connecting with a Hdmi to DVI cable External Equipment SetupWhen connecting with a Hdmi Hdmi in jack on the setDVD Setup Component Input portsSocket of the set When connecting with a Euro ScartWhen connecting Hdmi cable Please use shielded scart cableVCR Setup When connecting with an antennaInsertion of CI Module Connect the Euro scart socket of the VCR to the EuroPC Setup When connecting with a D-sub 15 pin cableExternal Equipment Setup When connecting with a DVI cableBack Cover for Wire Arrangement Hdmidtv supported mode RGB/DVIPCScreen Setup for PC Mode Select PictureAdjustment for screen Position, Size, Phase Selecting Resolution Select the desired resolutionAuto Configure RGB PC mode only Others ResolutionProgramme Selects a programme Remote Control KEY FunctionsNo function BType Subtitle Recalls your preferred subtitle in digital modeWatching TV /PROGRAMME Control Initializing setup Turning on the TVVolume Adjustment Programme SelectionOn Screen Menus Selection and Adjustment Display each menuAuto Programme Tuning Select SetupManual Programme Tuning in Digital Mode Select the desired channel numberManual Programme Tuning in Analogue Mode Normally fine tuning is only necessary if reception is poor Select Fine Fine tune for the best picture and soundProgramme Edit Select a programme to be stored or skippedDTV/RADIO Mode FAV Select your favourite pro- gramme numberSelect a programme number to be moved TV ModeGreen Start Auto Sort Yellow Release the moved programmeBooster in Digital Mode only OK SaveSoftware Update Diagnostics in Digital Mode only Information, language, or software download, etc CI Common Interface InformationSelect CI Information List Display the Programme List Select a programme OK Switch to the chosen programme numberSelecting the Programme Table Turns the pagesSelect a programme Switch on/off EPGSwitch on or off EPG Or PR Select desired programmeButton Function in 8 Day Guide Mode EPG Electronic Programme Guide in Digital ModeButton Function in NOW/NEXT Guide Mode Button Function in Date Change ModeButton Function in Extended Description Box Button Function in Record/Remind Setting ModeButton Function in Schedule List Mode Picture Control Picture Size Aspect Ratio ControlZoom1 Picture Control149 Preset Picture Settings Picture Mode-PresetAuto Colour Tone Control Warm/Medium/Cool VividAuto Colour Tone Control 6500K/9300KRGB,DVI mode only Choose one of two automatic colour adjustmentsManual Picture Adjustment Picture Mode-User optionSelect Picture Select Advanced Control Select your desired SourceAdvanced Film Mode Select Advanced Control Picture Reset Initialize the adjusted valueAuto Volume Leveler Sound & Language ControlSelect Audio Preset Sound Settings Sound ModeSound &LANGUAGE Control Sound Setting Adjustment User Mode Make desired adjustment BalanceSelect Dolby Digital or Selecting Digital Audio OUTSelect Digital Audio Out Select Audio Select TV Speaker Select On or Off TV Speakers ON/ OFF SetupYou can adjust the internal speaker status Audio Reset Stereo/Dual Reception In Analogue Mode Only Nicam Reception In Analogue Mode Only Speaker Sound Output SelectionSelect Option Sound & Language ControlIf you want to change Language/ Country selection Select your desired language or country OKSaveAudio Language Selection On the remote controlSelect your desired language OKSave Select On or Off Select the audio languageTime Setting Clock SetupTime Setting Auto ON/OFF Timer SettingAuto SHUT-OFF Setting Select Off or OnSelect Sleep Timer Time Zone SetupSleep Timer Setting 120, 180 or 240 MinInput Label Selects a label for each input sourceParental Control / Ratings KEY LockPower Indictor It helps you control LED when power is turned onDDC CIOnly RGB, DVI mode Initializing Reset to original factory settings Select Lock System Select On SET Password & Lock SystemInput a 4-digit password Block Programme Green Select a programme to be lockedParental Control in Digital Mode only Select LockTeletext PR+ or button can be used to select the previous or nextTeletext FastextDigital Teletext Troubleshooting Remote control Doesn’t work Power is suddenly Turned offAppendix Audio function does not workProduct is turned off From the web siteUser’s guide Is the screen position Wrong?Maintenance Cleaning the ScreenProduct Specifications M1994DM2094D M2294D Test your remote control Programming the Remote ControlProgramming a code into a remote mode Programming CodeVCR Repeat frame IR Codes1st frame Bit descriptionButton VOL + External Control Device Setup Pin NameSet ID Select Option Select Set IDCommand Reference List Transmission / Receiving ProtocolAck Kl Set ID DataCr Data 00 OSD off LSB Mb Set ID DataCr Data 00 Skip Add UK Only