Cisco Systems OSR-7609, 6509-NEB manual Connecting Power to the Fan Tray

Connecting Power to the Fan Tray

Figure 8 Installing the 3000 W Power Supply

48V INPUT 1

INPOUT POWER

HIGH SPEED FAN

48V INPUT 2

RTN		GOOD
	-48VDC GND
WS-C6500-NEB-FAN2
STATUS		STATUS		STATUS
2	1	2	1
				2	1
LINK		LINK
1				LINK1
		1
2		2
LINK		LINK		LINK2
4	3	4
			3	4	3
LINK		LINK		LINK3
3		3
4		4
LINK		LINK		LINK4
	LINK	RESET	LINK	RESET
RESET ALARMCARRIER			ALARMCARRIER
				ALARMCARRIER
1		1			ACTIVE
2		2		RX	TX
					RX
3				PORT1
		3
					TX
4		4		ALARMCARRIER
5					ACTIVE
		5
				RX	TX
6		6		PORT2	RX
7		7			TX
				ALARMCARRIER
8		8			ACTIVE
				RX	TX
					RX
				PORT3
					TX
				ALARMCARRIER
					ACTIVE
				RX	TX
					RX
					TX

STATUS

ACTIVE

NEXT SELECT

STATUS

ACTIVE

NEXT SELECT

STATUS		STATUS
2	1	2	1
LINK		LINK1
1
LINK		LINK2
2
4	3	4	3
LINK		LINK3
3
LINK		LINK4
4
RESET		RESET
ALARMCARRIER		ALARMCARRIER
	ACTIVE		ACTIVE
RX	TX	RX	TX
PORT	RX		RX
1		PORT1
	TX		TX
ALARMCARRIER		ALARMCARRIER
	ACTIVE		ACTIVE
RX	TX	RX	TX
PORT	RX		RX
2		PORT2
	TX		TX
ALARMCARRIER		ALARMCARRIER
	ACTIVE		ACTIVE
RX	TX	RX	TX
PORT	RX		RX
		PORT3
3
	TX		TX
ALARMCARRIER		ALARMCARRIER
	ACTIVE		ACTIVE
RX	TX	RX	TX
	RX		RX
	TX		TX

SUPERVISOR2

FAN FAIL INPOUT POWER
	GOOD
		RTN	-48VDC GND
STATUS	WS	SUPERVISOR2	STATUS	SUP2-
	-
	-			WS-
	X6K			X6K-
	-
	SUP2
SYSTEM	2GE		SYSTEM	2GE
CONSOLE			CONSOLE
PWR			PWR
MGMT			RESETMGMT
RESET

110-120V - 15A
200-240V - 15A
60/50HZ
	L	I
TAL
S	N
IN	RU
O				OUTPUT 42V	/
				42V
		INPUT		OK
			FAN OUTPUT		+
		OK	OK	FAIL

105070

Step 4 Tighten the power supply captive installation screw. (See Figure 7.)

Step 5 If you have a redundant power supply, install it now following the steps in this section.

Step 6 Proceed to the “Connecting Power to the Fan Tray” section on page 13 to connect power to the high speed fan tray.

Connecting Power to the Fan Tray

The high-speed fan tray requires external power, either from the 3000 W AC-input power supply or from an external DC power source. The fan tray ships with power wires secured at each terminal block.

If you are using the 3000 W AC-input power supply, use the supplied cables to connect the fan tray wires to the power supply.

If you are using a DC-input power supply, remove the wires from the fan tray and connect directly to a DC power source.

The following sections describe how to connect power to the fan tray:

•Installing the Fan Tray Power Cable for AC-Input Systems, page 14

•Connecting Site Power to the Fan Tray for DC-Input Systems, page 15

Catalyst 6509-NEB Switch and Cisco OSR-7609 Router Upgrade Note

78-16162-02 13