Onkyo Comprehensive Guide to Microphone Setup and Speaker Configuration for TX-NR636

2.After placing the microphone at the measurement position, select "Do it Now" with the cursors and press ENTER.

3.Connect the microphone to the SETUP MIC jack of the unit.

SETUP MIC jack

Speaker setup microphone

4.Follow the guidance displayed on the TV screen.

AccuEQ Room Calibration

Front Speakers Type	Normal
Powered Zone 2	No
Back/Height	Back
Subwoofer	Yes

Set bi-amp only if you use 2 channel amp for each front speaker.

ENTER Next

When the screen above is displayed, set the items with the cursors on the remote controller. When the cursor is on an item, the content of the item will be shown on the lower left of the screen. After setting the items, press ENTER on the remote controller. Press ENTER also in the next screen,

5.The test tones sound from the connected speakers and automatic speaker setting starts. Measurement will be made twice for each speaker. It takes several minutes to be completed. Keep the room as quiet as possible during measurement. If any of the speakers do not produce the test tone, check for disconnection.

6.When the measurement is completed, the measurement result is displayed.

Press t/u on the remote controller to check the settings. Press ENTER with "Save" selected. In the next screen showing that "AccuEQ" is "On", press ENTER on the remote controller.

•If there is an error message, follow the on-screen instruction to remove the error cause.

7.When "Please unplug setup microphone." is displayed, disconnect the microphone.

2nd Step : Source Connection

You can check whether or not each input source is connected correctly.

1.When the Source Connection start screen is displayed, select "Yes, Continue" with the cursors and press ENTER.

Initial Setup

Source Connection

This step will start to check if the connections were made correctly. Would you like to continue?

Yes. Continue

No. Skip

HOME Exi t

2.Select the desired input to check the connection and press ENTER.

Start playback of the selected device. If connection is correct, video/audio of the input source selected on the unit will be played.

3.After checking the connection, select "Yes" with the cursors and press ENTER.

•If you select "No" and press ENTER, the error cause will be displayed. Follow the guidance to remove the error cause and check the connection again.

4.Select "Yes" with the cursors and press ENTER on the remote controller to check the connection of other inputs or select "No, Done Checking" and press ENTER to skip.

If you select "Yes", you will return to the screen of step 2. If you select "No, Done Checking", you will proceed to step 5.

5.Enabling HDMI Linked Operation and Other Functions

In the next screen, you can enable the HDMI linked operation with CEC compliant device, connection with ARC compatible TV, and HDMI Through function. Select "Yes" with the cursors to enable them or "No, Done Checking" to skip, and press ENTER on the remote controller.

Step 2: Setting Up

6.Select "Yes" with the cursors and press ENTER to enable the CEC link function or select "No" and press ENTER to keep it disabled.

Source Connection

The following CEC-compatible devices are found;

Do you wish to turn on the CEC link?

Integra DHS-8.8

Yes

No

HOME Exi t

If you select "Yes", the connection with ARC compatible TV and HDMI Through function will be set to "Auto" and enabled.y

3rd Step : Remote Mode Setup

In this step, you can enable operation of the other components using the remote controller of the unit. When the Remote Mode Setup start screen is displayed, select "Yes" with the cursors and press ENTER on the remote controller. Follow the guidance to select the desired REMOTE MODE button and in the keyboard screen, enter the first three characters of the brand name of the device you are going to program (e.g., "ONK" for ONKYO) and search for the remote control code. The guidance will also explain how to set the remote controller.

Initial Setup

Remote Mode Setup

Preprograming remote will give you control of other devices from AV receiver remote Would you like to setup your remote to control your devices? This may take a while depending on what and how many you have connected. You can always come back to remote setup from setup “8-2 Remote Mode Setup”.

Yes

No. Skip

HOME Exit

8