Mitsubishi Electronics WD620U-G, XD600U-G user manual Basic operation, Power-on

Basic operation

ON STANDBY

4

6

FOCUS	3	1, 2
	MAGNIFY	ASPECT
ZOOM		UP
	VOL	PAGE
	KEYSTONE	DOWN
		AUTO
	MENU	POSITION

ENTER

		AV
		MUTE	FREEZE
		VIEWER	VIDEO
		1
		COMPUTER	S-VIDEO	5
		2
		UNPLUG
5	3, 1, 2	WIRELESS DVI	HDMI

Power-on				•	Images may not be projected with good quality in an extremely hot
1.	Turn on the device connected to the projector first.				or cold environment. (This is not a product malfunction.)
2.	Plug the power cord in the wall outlet.			• In order to ensure the safety in case of trouble with the projector,
					use an electrical outlet having an earth leakage breaker to supply
	• The POWER indicator lights up.
					the power to the projector. If you do not have such outlet, ask your
	• If the power cord is unplugged from the wall outlet before the
					dealer to install it.
	projector is cooled down completely after use, the fans may
				4.	Adjust the focus by turning the focus ring.
	start rotating when the power cord is plugged in next time
	and the POWER button may not function. In this case, wait			5.	Choose your desired external input source using the COM-
	for the fans to stop and press the POWER button to light the				PUTER, VIDEO or HDMI button.
	indicator.				• The input source is switched between COMPUTER1,
3.	Press the POWER button on the control panel or the ON button				COMPUTER2, and HDMI at every press of the COMPUTER
					button on the control panel.
	on the remote control.
	• It may take about one minute for the lamp to light up.				• The input source is switched between VIDEO and S-VIDEO
	• The lamp occasionally fails to light up. Wait a few minutes				at every press of the VIDEO button on the control panel.
	and try to light the lamp again.				• When pressing COMPUTER (1 or 2), HDMI, VIDEO, or S-
	• After the POWER button is pressed, the image may flicker				VIDEO button on the remote control, the input source
					switches directly as the button pressed.
	before the lamp becomes stable. This is not a product mal-
	function.				• The projector automatically selects the appropriate signal
	• Regardless of the setting of LAMP MODE in the INSTALLA-				format. The selected signal format is displayed on the
					screen.
	TION menu, the STANDARD lamp mode is activated by
	default whenever the projector is turned on. The LAMP				• The COMPUTER, VIDEO and HDMI buttons don’t function
	MODE is set to either STANDARD or LOW depending on the				while the menu is being displayed.
	setting last selected, and you cannot switch the LAMP				• When COMPUTER is chosen as the source, images sup-
	MODE in about one minute after the lamp is on.				plied from the computer may flicker. Press the W or X button
					on the remote control to reduce flicker, if it occurs.
	Indicator	STATUS	POWER		• To avoid permanently imprinting a fixed image onto your pro-
Condition
					jector, please do not display the same stationary images for
	Stand-by	-	Red		long period.
				6.	Adjust the image size by turning the zoom ring.
	When the lamp is on.	Green	Green
					• If necessary, adjust the focus and zoom again.

Important:

•If the lamp exceptionally turned off due to the power interruption or voltage drop, it can happen that the lamp does not turn on even if you switch again the power supply on. In that case, please pull the electric cord out of the consent and put it again in the consent about 10 minutes later.

•Do not cover the lens with the lens cap while the lamp is on.

•The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

•By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 37 and 40.)

When fine streaks are seen on projected images

This is due to interference with the screen surface and is not a mal- function. Replace the screen or displace the focus a little.

EN-16