Mitsubishi Electronics XD110, SD110 user manual Caution To Reduce The Risk Of Electric

Page 2
CAUTION : TO REDUCE THE RISK OF ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC

SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of suffcient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operat- ing and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTE:

SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIP- MENT AND SHALL BE EASILY ACCESSIBLE.

WARNING

Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception.

Use the attached RGB cable with this equipment so as to keep interference within the limit of an FCC Class B device.

This apparatus must be grounded.

DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equip- ment, ANSI/NFPA 75.

The attached power cords are to be used exclusively for this product. Never use them for other products.

When using the projector in Europe:

COMPLIANCE NOTICE

This Projector complies with the requirements of the EC Direc- tive 89/336/EEC "EMC Directive" as amended by Directive 92/ 31/EEC and 93/68/EEC, and 73/23/EEC "Low Voltage Direc- tive" as amended by Directive 93/68/ EEC.

The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of opera- tion are characterized by their connection to the public low volt- age power supply system.

WARNING

Use the attached RGB cable with this equipment so as to keep interference within the limits of an EN55022 Class B device.

Please follow WARNING instructions.

Note: This symbol mark is for EU countries only.

This symbol mark is accord- ing to the directive 2002/96/ EC Article 10 Information for users and Annex IV.

Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and reused.

This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste.

Please, dispose of this equipment at your local community waste collection/ recycling centre.

In the European Union there are separate collection systems for used electrical and electronic product.

Please, help us to conserve the environment we live in!

EN-2

Image 2
Contents This User Manual is important to you Please read it before using your projectorMODEL ENGLISHSHOCK DO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDE When using the projector in Europe COMPLIANCE NOTICECAUTION TO REDUCE THE RISK OF ELECTRIC REFER SERVICING TO QUALIFIED SERVICE PERSONNELDeclaration of Conformity ContentsImportant safeguards Trademark, Registered trademarkImportant safeguards Do not unplug the power cord during operation Do not keep using the damaged projectorDo not look into the lens when the projector is oper- ating Do not look into the air outlet grilles when projector is operatingTerminal board OverviewControl panel 10 11Remote control Bottom sideOperation range of the remote control Remote controlBattery installation Reception angle verticalFront projection InstallationLayout of the projector Front projection, ceiling mountingProjector + DVD player or HDTV decoder Basic connectionsProjector + AV device For Macintosh Projector + ComputerFor computer with Mini D-SUB About DDCPreparation Adjustment of the projection angleAfter using the projector Preparation for projection3, 1 Power-onBasic operation Basic operation continued Power-offVolume from the speaker AUTO POSITION buttonXGA60 Menu operationBasic operation 1 IMAGE 2 INSTALLATIONMenu operation continued 5 SIGNAL - USER No need to adjust in normal use 3 FEATURE4 SIGNAL To adjust the red-green color balance of the image Image adjustmentImage adjustment To adjust the detail and clarity of the imageWhen the image flickers or the image is out of focus Adjustment of the image from the computerSimple adjustment method When the top part of the image flagsTo resume the motion in the image Advanced featureStill Page-up and page-downTo enable the password function Password functionTo cancel the password function Reset of the lamp operation time Lamp replacementInterval of lamp replacement Problem TroubleshootingImages aren’t projected on the screen Cause and solutionTroubleshooting continued Images aren’t projected correctlyCleaning of the lens MaintenanceCleaning of the projector and the ventilation slots OthersAbnormal condition IndicatorsNormal condition Kensington Technology Group 2855 Campus Drive SpecificationsKensington Lock San Mateo, CA 94403, U.S.ADimensional drawings unit mm Specifications continuedConnectors What’s included in the boxSpecification of RGB signals in each computer mode of the projector Some computers aren’t compatible with the projectorNorth America MITSUBISHI Projector Contact InformationMITSUBISHI ELECTRIC CORPORATION Europe