Mitsubishi Electronics SL4U, XL8U user manual Basic operation, Power-on

Page 13

Basic operation

POWER STATUS

3, 1, 2

AUTO POSITION

 

 

COMPUTER

KEYSTONE

VIDEO

5

 

ENTER

5

 

MENU

 

 

POWER

PAGE

3, 1, 2

DOWN UP

4

6

5

SOURCE

KEYSTONE

AUTO

 

 

POSITION

 

 

 

STILL

 

MUTE

 

 

 

 

ENTER

 

 

 

 

MENU

 

PinP

 

 

 

 

VOLUME

 

 

 

EXPAND

 

 

ENGLISH

Power-on

1.Turn on the device connected to the projector first.

2.Plug the power cord in the wall outlet.

The POWER indicator lights up.

If the power cord is unplugged from the wall outlet before the projector is cooled down completely after use, the fans may start rotating when the power cord is plugged in next time and the POWER button may not function. In this case, wait for the fans to stop and press the POWER button to light the indicator.

3.Press the POWER button.

It may take about one minute for the lamp to light up.

The lamp occasionally fails to light up. Wait a few minutes and try to light the lamp again.

After the POWER button is pressed or the lamp mode is switched, the image may flicker before the lamp becomes stable. This is not a product malfunction.

The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW lamp mode has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1.5 minutes.

Indicator

STATUS

POWER

Condition

 

 

Stand-by

-

Red

When the lamp is on.

Green

Green

When the lamp is off temporarily.

-

Red

 

 

 

Important:

The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 26 and 29.)

Images may not be projected with good quality in an extremely hot or cold environment. (This is not a product malfunction.)

4.Adjust the focus by turning the focus ring.

5.Choose your desired external input source using the SOURCE button on the remote control or the COMPUTER or VIDEO button on the control panel.

The input source is switched between VIDEO, S-VIDEO and COMPUTER at every press of the SOURCE button on the remote control.

The input source is switched between VIDEO and S-VIDEO at every press of the VIDEO button on the control panel.

The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen.

The COMPUTER, VIDEO, and SOURCE buttons don’t function while the menu is being displayed.

Images supplied from the computer may flicker. Press the $ or % button on the remote control to reduce flicker, if it occurs.

6.Adjust the image size by turning the zoom ring.

• If necessary, adjust the focus and zoom again.

EN – 13

Image 13
Contents 8 S L Compliance Notice When using the projector in EuropeContents Important safeguards Do not look into the lens when the projector is operating Do not keep using the damaged projectorDo not unplug the power cord during operation Clean the air-filter once a monthControl panel OverviewTerminal panel 3 4Bottom side Remote controlBattery loading Remote controlOperation range of the remote control Layout of the projector InstallationFront projection Front projection, ceiling mountingProjector + AV device Basic connectionsProjector + DVD player or Hdtv decoder VCR, etcFor Macintosh Projector + ComputerComputer About DDCPreparation Adjustment of the projection anglePreparation for projection Basic operation Power-onVolume from the speaker Power-offBasic operation Auto Position buttonMenu operation InstallationBasic operation Menu operation Terminal when Video is chosen as the source. Select Expand Mode .. Choose the mode for enlarging the image. SeeComputer Video mode to always output the audio that is Selected, the film mode will not be activatedImage adjustment Image adjustmentColor temperature About color temperatureSimple adjustment method Adjustment of the image from the computerExpand Advanced featuresStill For XL8U only Picture in Picture PinPSetting procedure Setting of the image displayed during startup or mutingSet the background color Set the image sizePage-up and page-down Advanced featuresConnection To USB portTo cancel the password function Password functionTo enable the password function Reset of the lamp operation time Lamp replacementInterval of lamp replacement Cleaning of the air-filter Filter cover MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lensImages arent projected on the screen TroubleshootingImages arent projected correctly Others TroubleshootingPower Status IndicatorsNormal condition Abnormal conditionKensington Lock SpecificationsDimensional drawings unit mm ConnectorsReplacement part Option / Not included in the box What’s included in the boxXGA85 SpecificationsPC98 Mitsubishi Electric Corporation
Related manuals
Manual 5 pages 5.64 Kb Manual 5 pages 32.76 Kb