Mitsubishi Electronics SL4U Adjustment of the image from the computer, Simple adjustment method

Page 19

Adjustment of the image from the computer

This projector adjusts the format of the video signal supplied from the computer. However, sometimes images are not projected correctly owing to the type of the computer used. When the image from the computer isn’t projected correctly, press the AUTO POSITION button. (See page 14.) If the image isn’t projected correctly yet, adjust the image from the computer using the menu.

Important:

Do not change any of the settings in the SIGNAL- USER menu for normal use.

Simple adjustment method

1.

Select HORIZ. POSITION in the SIGNAL menu.

2.

Press the $ or % button to adjust the horizontal

 

start position (or the left side of the image).

3.

Select TRACKING in the SIGNAL menu.

ENGLISH

opt.

SIGNAL

XGA60

4. Press the $ or % button to adjust the horizontal

end position (or the right edge of the image).

 

HORIZ. POSITION

 

0

 

 

 

 

 

 

 

 

VERT. POSITION

 

0

 

 

 

 

 

 

 

 

FINE SYNC.

 

0

 

 

 

 

 

 

 

 

 

TRACKING

 

0

 

 

 

 

 

 

 

 

 

COMPUTER

RGB

 

RRGGBB INPUT

 

 

 

 

 

 

 

HOLD

 

ON

 

 

 

 

 

 

 

 

 

USER

 

OK

 

 

To move the image horizontally :

Adjust HORIZ. POSITION in the SIGNAL menu. Press the % button to move the image to the left. Press the $ button to move the image to the right.

To move the image vertically :

Adjust VERT. POSITION in the SIGNAL menu. Press the % button to move the image upward. Press the $ button to move the image downward.

When the image flickers or the image is out of focus :

Adjust FINE SYNC. in the SIGNAL menu.

When the top part of the image flags :

Change the setting of HOLD in the SIGNAL menu. Select ON , press the ENTER button, and adjust BEGIN or END to minimize the flagging.

SIGNAL-USER

 

 

 

 

 

 

 

 

CLAMP

 

0

 

 

POSITION

 

 

 

 

 

 

 

CLAMP WIDTH

 

1

 

 

 

 

 

 

 

 

 

 

?

VERT. SYNC.

 

AUTO

 

 

 

 

 

 

SHUTTER (U)

 

0

 

 

 

 

 

 

SHUTTER (L)

 

0

 

 

 

 

 

 

SHUTTER (LS)

 

0

 

 

 

 

 

 

SHUTTER (RS)

 

0

 

 

 

 

 

When wide strips appear :

Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL - USER menu.

When the motion doesn't run smoothly :

Adjust VERT. SYNC. in the SIGNAL - USER menu. Select AUTO for normal use.

When noise appears on the right or left half of the image :

Adjust SHUTTER (LS) or SHUTTER (RS) in the SIGNAL - USER menu.

When noise appears on the top or bottom part of the image :

Adjust SHUTTER (U) or SHUTTER (L) in the SIGNAL - USER menu.

5.

Repeat steps 1 to 4 for optimum adjustment

 

results.

6.

Select VERT. POSITION in the SIGNAL menu.

7.

Press the $ or % button to adjust the vertical

 

start position (or the upper edge of the image).

EN – 19

Image 19
Contents 8 S L Compliance Notice When using the projector in EuropeContents Important safeguards Clean the air-filter once a month Do not keep using the damaged projectorDo not look into the lens when the projector is operating Do not unplug the power cord during operation3 4 OverviewControl panel Terminal panelBottom side Remote controlBattery loading Remote controlOperation range of the remote control Front projection, ceiling mounting InstallationLayout of the projector Front projectionVCR, etc Basic connectionsProjector + AV device Projector + DVD player or Hdtv decoderAbout DDC Projector + ComputerFor Macintosh ComputerPreparation Adjustment of the projection anglePreparation for projection Basic operation Power-onAuto Position button Power-offVolume from the speaker Basic operationMenu operation InstallationBasic operation Menu operation Selected, the film mode will not be activated Expand Mode .. Choose the mode for enlarging the image. SeeTerminal when Video is chosen as the source. Select Computer Video mode to always output the audio that isAbout color temperature Image adjustmentImage adjustment Color temperatureSimple adjustment method Adjustment of the image from the computerFor XL8U only Picture in Picture PinP Advanced featuresExpand StillSet the image size Setting of the image displayed during startup or mutingSetting procedure Set the background colorTo USB port Advanced featuresPage-up and page-down ConnectionTo cancel the password function Password functionTo enable the password function Reset of the lamp operation time Lamp replacementInterval of lamp replacement Cleaning of the lens MaintenanceCleaning of the air-filter Filter cover Cleaning of the projector and the ventilation slotsImages arent projected on the screen TroubleshootingImages arent projected correctly Others TroubleshootingAbnormal condition IndicatorsPower Status Normal conditionKensington Lock SpecificationsWhat’s included in the box ConnectorsDimensional drawings unit mm Replacement part Option / Not included in the boxXGA85 SpecificationsPC98 Mitsubishi Electric Corporation
Related manuals
Manual 5 pages 5.64 Kb Manual 5 pages 32.76 Kb