Mitsubishi Electronics XD280U-G, XD250U-G user manual Remote control, Battery installation

Page 8

Remote control

Battery installation

Use two (AA, R6) size batteries.

1.Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.

2.Load the batteries making sure that they are positioned correctly (+ to +, and - to -).

• Load the batteries from - spring side, and make sure to set them tightly.

3.Replace the back cover.

Caution:

Use of a battery of wrong type may cause explosion.

Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

Dispose of used batteries according to your local regulations.

Batteries may explode if misused. Do not recharge, disassemble, or dispose of in fire.

Be sure to handle the battery according to the instructions.

Load the battery with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

Keep batteries out of reach of children and pets.

Remove the battery, if the remote control is not used for a long time.

Do not combine a new battery with an old one.

If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

Operation range (of the remote control)

The maximum operation distance of the remote control is about 10 m (or about 32 feet) when the remote control is pointed at the remote control sensor of the projector. When the remote control is pointed to the screen, the distance from the remote control to the projector via the screen should be 5 m or less. However, the operation distance varies depending on the type of the screen used.

Reception angle (vertical)

Reception angle (horizontal)

Reception angle (vertical), ceiling mount

Important:

Do not expose the remote control sensor to direct sunlight or fluorescent. Keep a distance at least 2 m (6.5 feet) between the remote control sen- sor and the fluorescent light to ensure correct operation of the remote control.

Inverted fluorescent light, if located near the projector, may interfere the remote control.

When you use the remote control too close to the remote control sensor, the remote control may not work correctly.

EN-8

Image 8
Contents XD250U XD250U-G XD280U XD280U-G When using the projector in Europe only for XD250U/ XD280U ShockContents Important safeguards Do not keep using the damaged projector Do not look into the lens when the projector is operatingDo not unplug the power cord during operation Place of installationOverview Control panel Terminal board10 12 Kensington LockBottom side Remote control OverviewOperation range of the remote control Remote controlBattery installation Layout of the projector InstallationCeiling Mount Installation Projector + DVD player or Hdtv decoder Basic connectionsProjector + AV device Hdmi Basic connectionsConnection for video equipment having an Hdmi terminal Projector + Computer Adjustment of the projection angle Using the adjustment feet frontPreparation Preparation for projectionBasic operation Power-onWhen fine streaks are seen on projected images Basic operation When connecting to a laptop computer Wall ScreenMenu operation Quick Menu Basic operationQuick Menu Color Enhancer Auto Presentation ContrastInformation menu Menu operationMenu Options Detail Menu Image Advanced menu Basic operationImage menu Installation menu Feature menu Signal User menu Singal menuNetwork menu MenuEN-24 Image adjustment Adjusting projected imagesGamma mode Color EnhancerImage adjustment Simple method to adjust the image positionBrilliantColorTM LPF Progressive filterNetwork settings Setting Projector NameNetwork Password Settings IP SettingsNetwork settings How to Use Network Function GlossaryFreeze Advanced featuresPassword function Advanced features To cancel the password functionTo use the Magnify mode MagnifyConnection Supervising and controlling by computerMajor functions Lamp replacement When the projector is mounted to the ceilingReset of the lamp operation time Lamp replacementInterval of lamp replacement No image appears on the screen TroubleshootingPower Status LPF TroubleshootingImages are not displayed correctly Maintenance Cleaning of the projector and the ventilation slotsCleaning of the lens OthersAbnormal condition IndicatorsNormal condition Specifications Specifications ConnectorsDimensional drawings unit mm Replacement partCGA84 CGA85VGA60 VGA72Mitsubishi Electric Corporation