Mitsubishi Electronics XD200U, SD200U Lamp replacement, Interval of the lamp replacement

Page 22

Lamp replacement

When the lamp no longer functions, replace it with a new one.

Caution:

• Do not remove the lamp immediately after turn-

ing off the projector, the high temperature of the

lamp can burn you.

• For lamp replacement, press the power button to

power off, then wait for 120 seconds in stand-by

mode to allow the lamp to cool. Then turn off the

main switch, unplug the power cord from the

outlet, and wait one hour so that the lamp is

cooled to the touch.

7.Put the handle back to the holding point.

Make sure that the handle is locked.

8.Tighten up the screws (b) using a phillips screwdriver (+).

9.Tighten up the screws of the lamp lid (a) using a phillips screwdriver (+).

(b)Handle

(a)

• Do not remove the lamp except for replacement.

Careless treatment can cause injury or fire.

• Do not touch the lamp element directly. It may

break and cause you to injure or burn yourself.

• Be sure not to drop the lamp lid screw into the

projector. Also be sure not to insert metal or any

flammable objects, it may cause fire or electric

shock. If any objects are inserted, please unplug

and contact your dealer.

• Install the lamp securely, failure may cause a fire.

• If the light bulb part breaks, some small glass

fragments may fall out through the small cooling

grille, and stick to the inside of projector or the

lamp box. When taking the lamp out, make sure to

turn over the projector and hold the handle of the

lamp box to avoid injury from the glass fragments.

• Never shake the lamp or hold it in front of your face

after removingthe lamp box. The glass fragments

may fall out and cause injuries to your eyes and so

on.

How to reset the operation time meter Plug in the power cord, turn on the main power switch, and reset lamp time by pressing the AUTO POSITION button and POWER button for 3 seconds simultaneously.

Make sure that the STATUS indicator flashed twice and the operation time meter has been reset.

Caution:

Do not spill liquid on the lamp or place it near flammable objects or where children can touch it. Otherwise, it could cause injury or fire.

Be sure that the projector guide is firmly inserted between the right and left lamp guides.

Important:

The projector will not turn on if you do not secure

 

the lamp lid.

You must reset the operation time meter after

 

you replace the lamp.

1.Gently turn the projector over.

2.Loosen the screws of the lamp lid (a) using a phillips screw- driver (+), and remove the lid.

Remove the lamp cover in the direction of the arrow as indicated.

3.Loosen screws (b) using a phillips screwdriver (+).

4.Pull up the handle.

5.Hold onto the projector by the handle as you pull out the lamp.

Pull out the lamp straight upward.

Pull the lamp out of the projector slowly. Should the light bulb be broken, glass fragments will spill out if the lamp is pulled out too quickly.

Once the lamp has been removed, do not spill liquid on it, place it near flammable objects or where children can touch it. Otherwise, it may cause injury or fire.

6.Insert the new lamp securely into the projector body in the right direction.

(a)

(b)Handle

• Do not reset the operation time meter unless the

lamp has been replaced.

Interval of the lamp replacement

The expected lamp lifetime is about 1,500 hours of operation. However, the lamp life may differ accord- ing to the operat-ing environment and may be shorter than 1,500 hours. Decreases in brightness will indicate that the projector lamp needs to be replaced. When lamp operation time exceeds 1,000 hours, the indicator will flash alternately between green and red (while the lamp is in operation; when the lamp is not in operation, the STATUS indicator will appear red only). When the lamp has been used for about 1,400 hours, the message “LAMP!!.” will appear on the screen for one minute everytime the power is turned on. When the lamp has been used for about 1,500 hours, the projector will automatically shut off for safety and the power and STATUS indicators light will be red. The projector cannot be used until the lamp has been replaced and operation timer has been reset.

Caution:

The lamp is fragile. If broken, be careful not to cut yourself with glass fragments.

The replacement span of the lamp depends on the environment. For replacement lamps, please contact your dealer.

The projector automatically shuts off when the lamp life exceeds 1,500 hours and cannot be used until the lamp is replaced and the internal timer is reset.

EN – 22

Image 22
Contents SD200 When using the projector in Europe Compliance NoticeContents Important safeguards Do not modify this equipment Do not touch Air outlet grilleNever remove the cabinet If you break or drop the cabinetOverview Terminal boardAbout laser beam Remote controlRear adjustment feet Lamp cover Front adjustment feet Beam Divergence 6m distance about 10mm x 10mm ± 6mmBattery installation Using the remote controlOperation area Orientation of the projector InstallationScreen Projector + DVD player or Hdtv decoder Basic connectionsProjector + AV equipment Speaker output is monoAbout DDC For Computer 1 in connector For using MacintoshProjector + Personal computer Preparing the projector for operation Adjusting the angle of projectionGetting ready for projection Zoom ring To operate projector power onFocus ring Far Near Tele WideTurning off the projector Volume from the speakerAV mute Menu operation Basic operationLamp is off. Use the remote control to turn on Reproducibility When sRGB is ON, Color Matrix can’t be adProjector will be in the stand-by mode when Higher as the number increasesUse to synchronize the projector with PC input signals Use to adjust the horizontal position of the imageUse to adjust the vertical position of the image This will be set automatically to match the input signalColor temperature Picture adjustmentAdjusting the image Color matrixAdjustment from personal computer Real screen display Advanced features for presentationExpand Picture in Picture PinPConnection Mouse remote controlOperation Lamp replacement Interval of the lamp replacementIndicators MaintenanceTroubleshooting Specifications Replacement part Option / Not included in the box ConnectorsDimensional drawings mm What’s included in the boxCGA70 640 x 31.47 70.09 800 x Page 871D349A10 Interface Control projector by using a personal computerControl command diagram ConnectionHow to set the grade Operation commandsVolume commands Control sequenceMenu setting commands Remote commandsReading command diagram Example Display Menu selection bar. is for Ascii codeExample Set the Mute to on