Mitsubishi Electronics HC910 Connecting to a video player, etc, Connecting to a DVD player, EN-13

Page 13

Connecting to a video player, etc.

Connecting to a video player, etc.

Video player, or the like

	2
COMPONENT VIDEO IN	To video out-
	put terminal
S-VIDEO IN	1 INTo terminalVIDEO
VIDEO IN
	Video cable
	Video player, or the like
S-video cable
	To S-video output
1To S-VIDEO	2 terminal
IN terminal

COMPONENT VIDEO IN

S- IN

VIDEO IN

1.Connect one end of the optional video cable to the VIDEO IN terminal of the projector.

2.Connect the other end of the video cable to the video output terminal of the video equipment.

When the video equipment is equipped with the S-video output terminal, make the connection as follows.

1.Connect one end of the optional S-video cable to the S-VIDEO IN terminal of the projector.

2.Connect the other end of the S-video cable to the S-video output terminal of the video equipment.

ENGLISH

•Also read the instruction manual of the equipment to be connected.

•Contact your dealer for details of connection.

When a TV tuner or VCR is connected:

When you use this projector with a TV tuner or VCR connected, no image may appear or a message of NO SIGNAL may appear on the screen when you change the channel via any channel that is not being received. In such a case, set the channels of the TV tuner or VCR again. To avoid such symptom, use the TV tuner or VCR with its channel skip function (that is a function not to display channels that are not being received) enabled.

Connecting to a DVD player

To connect this projector to video equipment that has component video output terminals, such as a DVD player, use the COMPONENT terminals.

Component cable (Option)	PB/CB
Y	PR/CR

COMPONENT VIDEO IN

S-VIDEO IN

VIDEO IN

PR/CR PB/CB Y

DVD player

•Images may not be projected correctly depending on the type of the DVD player you use.

•Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

EN-13

Image 13

Contents HC910 MODELHC910 User ManualREFER SERVICING TO QUALIFIED SERVICE PERSONNEL SHOCK, DO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDEWhen using the projector in Europe COMPLIANCE NOTICE CAUTION TO REDUCE THE RISK OF ELECTRICDeclaration of Conformity ContentsTrademark, Registered trademark EN-4 Important safeguardsDo not look into the air outlet grille when projector is operating Do not look into the lens when it is operating. It may hurt your eyesPlace of installation Unplug immediately if there is something wrong with your projectorInserting the batteries into the remote control Checking accessoriesPreparing your projector Power supply partsControl area OverviewTerminal panel 5 Remote control sensor Front 6 Air inlet grille 7 Air outlet grilleUsing the picture quality adjusting buttons Remote controlPreparating your projector Continue Bottom sideOperational range of the remote control Using the remote controlReception angle Front of projectorSetting up the screen Setting up your projectorBasic setup Adjusting the projection angleScreen size and projection distance When the aspect ratio of the screen isEN-11 Viewing video images A. Connecting the projector to video equipmentBasic home theater system connection PreparationConnecting to a DVD player Connecting to a video player, etcWhen a TV tuner or VCR is connected EN-13Connecting to video equipment having a DVI-D terminal B. Plugging in the power cordViewing video images continued EN-15 C. Projecting imagesTo stop projecting When projected images are distorted to a trapezoidIRIS button With the INSTALLATION menuHow to change the settings Setting the aspect ratioWith the remote control With the FEATURE menuB. Plugging the power cord A. Connecting the projector to a computerViewing computer images For analog connectionEN-19 C. Projecting imagesViewing computer images continued When connecting to a notebook computerAUTO POSITION button Example of the setting procedure for external outputMenu operation How to set the menusMenu operation continued Available settings in the menus2. INSTALLATION menu 1. IMAGE menu4. SIGNAL menu 3. FEATURE menuEN-23 AUTOTo adjust the brightness CONTRAST and BRIGHTNESS Adjusting projected imagesTo adjust the color COLOR and TINT To sharpen or soften the projected image SHARPNESSTo adjust the tone of white To customize the color temperature To adjust the tone of white COLOR TEMPAbout color temperature AV MEMORYHow to adjust the image supplied from the computer using the menu Adjusting projected images continuedSimple method to adjust the image position To adjust the horizontal positionPassword function Advanced featuresTo enable the password function To cancel the password functionDimension Drawings unit mm Asking for installationTo view images projected on the translucent screen from behind Installation Using ﬁlterCleaning Cleaning the ﬁlterInterval of lamp replacement Replacing the lampEN-30 Cleaning of the projector and the ventilation slots MaintenanceCleaning of the lens To replace the lampProblem TroubleshootingSolution EN-32Images are not displayed correctly No image appears on the screen. ContinuedKensington Lock Troubleshooting continuedOthers Normal condition IndicatorsAbnormal condition Speciﬁcations Replacement part Option / Not included in the boxSpeciﬁcation of RGB signals in each computer mode of the projector ConnectorsEN-37 MITSUBISHI ELECTRIC CORPORATION MITSUBISHI Projector Contact Information871D420A70 Printed in Japan