Mitsubishi Electronics HC910 Preparating your projector Continue, Remote control, Bottom side

Page 8

Preparating your projector (Continue)

Preparating your projector (Continue)

Bottom side

1

2

3

1Adjustment foot (Front)

2Lamp cover

3Adjustment feet (Rear)

Caution:

Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.

Remote control

19

ON POWER OFF

1 18

2	DVI-D (HDCP)	COMPONENT		17
2	DVI	COMP	VIDEO	17
3	COMPUTER			16
3	PC		S-VIDEO	16
4				15
				15
		ENTER
5	MENU		ASPECT	14
6	AV MEMORY
6	M1	M2	M3
7	CONTRAST	BRIGHTNESS COLOR TEMP		13
7	CNT	BRT	C.T.	13
8		SHARPNESS		12
8	GAMMA	SHARP	IRIS	12
9	AUTO POSITION			11
	A.P.			10
	A.P.

1ON ( ) button

2DVI-D(HDCP) button

3COMPUTER button

4ENTER button

5MENU button

6AV MEMORY buttons

7CONTRAST button*

8GAMMA button*

9AUTO POSITION button

10SHARPNESS button*

11IRIS button

12BRIGHTNESS button*

13COLOR TEMP button*

14ASPECT button

15Direction buttons

16S-VIDEO button

17VIDEO button

18OFF () button

19COMPONENT button

* : See below for the picture quality adjusting buttons.

Important:

When you press any button on the remote control, the buttons on the remote control are lit. Wait approx. 5 seconds after releasing the button to turn them off.

Using the picture quality adjusting buttons

When you press any of the picture quality adjusting buttons, the screen for adjusting the picture quality appears. Ad- just the picture quality by pressing the and buttons. The picture quality adjustment can be made alternatively in the IMAGE menu. (See Page 22.) Items in the menus are shown in parentheses below.

CONTRAST (CONTRAST) ………… Adjust the contrast of the projected image.

GAMMA (GAMMA MODE) ………… Selects one of the preset gamma mode.

SHARPNESS (SHARPNESS) ……… Adjust the sharpness of the projected image.

BRIGHTNESS (BRIGHTNESS) …… Adjust the brightness of the projected image.

COLOR TEMP (COLOR TEMP.) …… Selects one of the preset color temperatures (HIGH BRIGHTNESS/9300K/6500K/

5900K/USER). Color adjustment of USER mode is also available. Select "USER" and press the ENTER button for color adjustment of USER mode. Use the or

button to select an item and or button to adjust the selected item. (Refer to page 25.)

EN-8

Image 8

Contents MODEL HC910HC910 User ManualSHOCK, DO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNELWhen using the projector in Europe COMPLIANCE NOTICE CAUTION TO REDUCE THE RISK OF ELECTRICTrademark, Registered trademark ContentsDeclaration of Conformity Important safeguards EN-4Do not look into the lens when it is operating. It may hurt your eyes Do not look into the air outlet grille when projector is operatingPlace of installation Unplug immediately if there is something wrong with your projectorChecking accessories Inserting the batteries into the remote controlPreparing your projector Power supply partsOverview Control areaTerminal panel 5 Remote control sensor Front 6 Air inlet grille 7 Air outlet grilleRemote control Using the picture quality adjusting buttonsPreparating your projector Continue Bottom sideUsing the remote control Operational range of the remote controlReception angle Front of projectorSetting up your projector Setting up the screenBasic setup Adjusting the projection angleEN-11 When the aspect ratio of the screen isScreen size and projection distance A. Connecting the projector to video equipment Viewing video imagesBasic home theater system connection PreparationConnecting to a video player, etc Connecting to a DVD playerWhen a TV tuner or VCR is connected EN-13Viewing video images continued B. Plugging in the power cordConnecting to video equipment having a DVI-D terminal C. Projecting images EN-15When projected images are distorted to a trapezoid To stop projectingIRIS button With the INSTALLATION menuSetting the aspect ratio How to change the settingsWith the remote control With the FEATURE menuA. Connecting the projector to a computer B. Plugging the power cordViewing computer images For analog connectionC. Projecting images EN-19When connecting to a notebook computer Viewing computer images continuedAUTO POSITION button Example of the setting procedure for external outputHow to set the menus Menu operationAvailable settings in the menus Menu operation continued2. INSTALLATION menu 1. IMAGE menu3. FEATURE menu 4. SIGNAL menuEN-23 AUTOAdjusting projected images To adjust the brightness CONTRAST and BRIGHTNESSTo adjust the color COLOR and TINT To sharpen or soften the projected image SHARPNESSTo adjust the tone of white COLOR TEMP To adjust the tone of white To customize the color temperatureAbout color temperature AV MEMORYAdjusting projected images continued How to adjust the image supplied from the computer using the menuSimple method to adjust the image position To adjust the horizontal positionAdvanced features Password functionTo enable the password function To cancel the password functionTo view images projected on the translucent screen from behind Asking for installationDimension Drawings unit mm Using ﬁlter InstallationCleaning Cleaning the ﬁlterEN-30 Replacing the lampInterval of lamp replacement Maintenance Cleaning of the projector and the ventilation slotsCleaning of the lens To replace the lampTroubleshooting ProblemSolution EN-32No image appears on the screen. Continued Images are not displayed correctlyOthers Troubleshooting continuedKensington Lock Abnormal condition IndicatorsNormal condition Replacement part Option / Not included in the box SpeciﬁcationsEN-37 ConnectorsSpeciﬁcation of RGB signals in each computer mode of the projector MITSUBISHI Projector Contact Information MITSUBISHI ELECTRIC CORPORATION871D420A70 Printed in Japan