Mitsubishi Electronics HC910 user manual Caution To Reduce The Risk Of Electric, EN-2

Page 2
CAUTION: TO REDUCE THE RISK OF ELECTRIC

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTE:

SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.

WARNING

Use the attached specified power supply cord. If you use another power-supply cord, it may cause interference with radio and television reception.

Use the attached RS-232C cable and RGB cable with this equipment so as to keep interference within the limit of a FCC Class B device.

This apparatus must be grounded.

DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75.

When using the projector in Europe:

COMPLIANCE NOTICE

This Projector complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” as amended by Directive 92/31/EEC and 93/68/EEC, and 73/23/ EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.

The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.

WARNING

Use the attached RS-232C cable and RGB cable with this equipment so as to keep interference within the limits of an EN55022 Class B device.

Please follow WARNING instructions.

EN-2

Image 2
Contents HC910 MODELHC910 User ManualWhen using the projector in Europe COMPLIANCE NOTICE SHOCK, DO NOT REMOVE COVER OR BACK NO USER-SERVICEABLE PARTS INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL CAUTION TO REDUCE THE RISK OF ELECTRICTrademark, Registered trademark ContentsDeclaration of Conformity Important safeguards EN-4Place of installation Do not look into the lens when it is operating. It may hurt your eyesDo not look into the air outlet grille when projector is operating Unplug immediately if there is something wrong with your projectorPreparing your projector Checking accessoriesInserting the batteries into the remote control Power supply partsTerminal panel OverviewControl area 5 Remote control sensor Front 6 Air inlet grille 7 Air outlet grillePreparating your projector Continue Remote controlUsing the picture quality adjusting buttons Bottom sideReception angle Using the remote controlOperational range of the remote control Front of projectorBasic setup Setting up your projectorSetting up the screen Adjusting the projection angleEN-11 When the aspect ratio of the screen isScreen size and projection distance Basic home theater system connection A. Connecting the projector to video equipmentViewing video images PreparationWhen a TV tuner or VCR is connected Connecting to a video player, etcConnecting to a DVD player EN-13Viewing video images continued B. Plugging in the power cordConnecting to video equipment having a DVI-D terminal C. Projecting images EN-15IRIS button When projected images are distorted to a trapezoidTo stop projecting With the INSTALLATION menuWith the remote control Setting the aspect ratioHow to change the settings With the FEATURE menuViewing computer images A. Connecting the projector to a computerB. Plugging the power cord For analog connectionC. Projecting images EN-19AUTO POSITION button When connecting to a notebook computerViewing computer images continued Example of the setting procedure for external outputHow to set the menus Menu operation2. INSTALLATION menu Available settings in the menusMenu operation continued 1. IMAGE menuEN-23 3. FEATURE menu4. SIGNAL menu AUTOTo adjust the color COLOR and TINT Adjusting projected imagesTo adjust the brightness CONTRAST and BRIGHTNESS To sharpen or soften the projected image SHARPNESSAbout color temperature To adjust the tone of white COLOR TEMPTo adjust the tone of white To customize the color temperature AV MEMORYSimple method to adjust the image position Adjusting projected images continuedHow to adjust the image supplied from the computer using the menu To adjust the horizontal positionTo enable the password function Advanced featuresPassword function To cancel the password functionTo view images projected on the translucent screen from behind Asking for installationDimension Drawings unit mm Cleaning Using filterInstallation Cleaning the filterEN-30 Replacing the lampInterval of lamp replacement Cleaning of the lens MaintenanceCleaning of the projector and the ventilation slots To replace the lampSolution TroubleshootingProblem EN-32No image appears on the screen. Continued Images are not displayed correctlyOthers Troubleshooting continuedKensington Lock Abnormal condition IndicatorsNormal condition Replacement part Option / Not included in the box SpecificationsEN-37 ConnectorsSpecification of RGB signals in each computer mode of the projector 871D420A70 MITSUBISHI Projector Contact InformationMITSUBISHI ELECTRIC CORPORATION Printed in Japan