Mitsubishi Electronics LVP-S120A user manual Focus ring Zoom ring, Turning off the projector

Page 16

To operate projector power ON (continue)

AUTO POSITION button

When the source is selected to RGB and the image is not in the right place, set to display as blight signal as possible, then press the AUTO POSITION button on the remote control. If the image is still not in the right place.

•Set screen to the brightest display as possible (e.g., full-screen display of the “Trash” window) before deploying the automatic adjustment function.

•If the screen saver is running, turn off the screen saver before using the automatic adjustment button.

5.Adjust the focus with the focus ring by turning it.

6.Adjust the image size with the zoom ring by turn- ing it.

focus ring

zoom ring

tele

near wide

far

The volume from the speaker

Press the volume + or – button to change the volume from the speaker.

30

•The volume buttons do not work when MENU se- lection bar or MENU is displayed.

•The volume buttons do not work when the source is selected to PC CARD.

Turning off the projector

7.Press the POWER button.

The message “POWER OFF? YES : PRESS AGAIN” appears on the screen.

•To exit from this mode, press any button except POWER, LASER, mouse pointer, R/L-click, STILL and VOLUME + and - button.

8.Press the POWER button again.

The light source lamp will be turned off.

Pressing the POWER button again will shut off the light source lamp, but the exhaust fan continues to operate for 120 seconds to cool down the light source lamp and LCD panels. In this time, the lamp indi- cator will be turned off from flashing.

9.Turn off the main power switch. When turning off the main switch, the POWER indicator turns off.

•In cases where the main power switch is acciden- tally turned off when either the intake/exhaust fan or the power source lamp is in operation, allow the unit to cool down for 10 minutes with the power turned off. Repeat step 3 when turning on the power source lamp. If the lamp does not turn on immediately, repeat this step two or three times. Replace the lamp if it should still fail to turn on.

Caution:

•When you have finished using this equipment, wait 120 seconds for the exhaust fans to stop. Then turn off the main switch and unplug the power cable from the wall outlet, for safety purposes.

•After the lamp is turned off, the lamp cannot be switched on again for 60 seconds as a precaution- ary measure. It will take another 60 seconds before the lamp indicator goes off. If you wish to turn on the projector again, wait until the indicator is off then press the POWER button.

•The exhaust fan runs rotate faster automatically when the temperature around the projector becomes high.

•When the temperature around the projector becomes much higher, the sign of “TEMP!!” blinks red on the screen. If the temperature stays in high, the lamp will be shut off automatically .

The projector automatically shuts off when the lamp is used up in about 2,000 hours and not used until lamp replacement.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents S120 Page Contents Important safeguards Never remove the cabinet Do not modify this equipmentIf you break or drop the cabinet Do not face a lens to the sunOverview of the projector Front Lamp lid Overview of the remote control About laser beamBattery installation Operation areaOrientation of the projector Preparing the projector for operationScreen Adjusting the angle of projection Getting ready for projectionGround Terminal Take off the lens capBasic connections Projector + AV equipmentCables and adapters Projector + DVD playerProjector + IBM PC or IBM PC compatibles Desktop computerPower Book When outputting to both a PC monitor and the projectorProjector + Macintosh DesktopTo operate projector power on Numbers 1 9 correspond to the instruction numbers belowVolume from the speaker Focus ring Zoom ringTurning off the projector Auto Position buttonSetting range is different according To the type of the signalMenu operation Basic operationMenu setting continue Signal Picture adjustment Adjustment from personal computerCGA70 Expand Advanced feature for presentationStill Using the PC-CARD Setting up the PC-CARDDuring PC-CARD playback, the sound is switched off Removing the PC-CARDPC-CARD Continue Advanced feature with PC Installation of softwarePCV PC Card Viewer EnvironmentCommand reference For Windows Starting up PCV For WindowsRecording the image For Windows Editing the presentation For Windows Starting up PCV For Macintosh Command referenceRecording the image For Macintosh Editing the presentation For Macintosh Mouse remote control ConnectionOperation Projector + IBM PC or IBM PC compatiblesReplacement of a light source lamp How to reset the operation time meter Life of the lampMaintenance Cleaning the air-filterCleaning the projector and the ventilation slots Cleaning the lensTroubleshooting Problems Cause Possible SolutionsIndicators Indicator Shows Condition Possible SolutionsReplacement parts list SpecificationsAccessories S120 Control this projector by using a personal computer Connection Projector + IBM PC or IBM PC compatiblesInterface Control command diagramControl sequence Operation commands Remote commandsReading command diagram Picture adjustment commands ColorMitsubishi Electronics AMERICA, INC

LVP-S120A specifications

The Mitsubishi Electronics LVP-S120A is a high-quality projector that has garnered attention for its impressive performance and advanced features, making it an excellent choice for both home theater enthusiasts and professional presentations. This model combines cutting-edge technology with user-friendly capabilities, ensuring an exceptional visual experience.

One of the main features of the LVP-S120A is its impressive brightness level, which is rated at 2,500 ANSI lumens. This allows the projector to deliver clear, vibrant images even in well-lit environments, making it a versatile option for various settings, such as classrooms, conference rooms, or living rooms. Coupled with a high contrast ratio, the projector provides sharp image details and deep blacks, enhancing the overall viewing experience.

The LVP-S120A utilizes LCD technology, which is known for its ability to reproduce accurate color and crisp imagery. This projector supports a native resolution of 800x600 pixels, offering a decent quality for standard presentations and video playback. Additionally, it supports various resolutions, making it compatible with a wide array of content sources, such as laptops, DVD players, and gaming consoles.

Another notable aspect of the LVP-S120A is its lightweight and compact design. Weighing just around 3.5 kilograms, it is highly portable, allowing users to easily transport it from one location to another. This feature is particularly advantageous for business professionals who need to deliver presentations on-site or educators who might move between classrooms.

Networking capabilities are also integrated into the LVP-S120A, which allows for easy connectivity to various devices. This projector is equipped with multiple input options, including HDMI, VGA, and composite video ports. The presence of these ports makes it straightforward to connect to a range of media devices, enhancing its versatility.

In terms of usability, the LVP-S120A is designed with user-friendly controls and provides intuitive settings that allow users to adjust image parameters easily. The remote control adds to the convenience of operation, enabling users to navigate through settings from a distance. Furthermore, the projector features an automatic keystone correction function, ensuring a perfectly aligned image even on tilted surfaces.

Overall, the Mitsubishi Electronics LVP-S120A stands out as a reliable projector that balances portability, ease of use, and impressive visual quality, making it an ideal choice for both personal and professional applications.
Top Page Image Contents