Onkyo HT-R420 appendix Audio adjust function, Before operating the remote control

Page 30

Audio adjust function

PRESET/ADJUST ™/£

AUDIO ADJUST

CINE FLTR

LATE NIGHT

AUDIO ADJUST

ADJUST 2/3

Before operating the remote control

Press RCVR/TAPE. This button may be in a slightly different position on your remote controller.

Using the audio adjust functions

Before operating the remote controller, press RCVR/TAPE.

These functions only work with speaker system A.

Audio Adjust provides various functions for adjusting the sound, including several especially for use with Dolby Digital, DTS, and Pro Logic II source.

The following table lists the Audio Adjust functions, their ranges and default values. Function availability depends on the current source and listening mode, as listed in the ÒThe input source and available listening modeÓ column. See page 29 for information on listening modes.

Function

Range

Default

Supported

 

 

 

listening mode

Bass

Ð12 dB to +12 dB

0 dB

All modes except

Treble

in 2 dB steps

Direct

 

Late Night

Low, High, Off

 

Dolby Digital

Cinema

 

 

Pro Logic II Movie

 

Off

Dolby Digital

Filter

On, Off

 

DTS

(Cine Fltr)

 

 

 

 

DTS Neo:6 Cinema

 

 

 

Panorama

On, Off

Off

 

Dimension

0, 1, 2, 3, 4, 5, 6

 

Pro Logic II Music

Center

0, 1, 2, 3, 4, 5, 6,

3

 

Width

7

 

 

 

 

 

 

1.Press AUDIO ADJUST (repeatedly) until the item to be adjusted is displayed.

2.Press PRESET/ADJUST ™/£ on the unit or ADJUST 2/3 on the remote controller to adjust the item.

Refer to the right column for AUDIO ADJUST items and settings.

Item

Value or setting

Note

Cinema Filter and Late Night can also be adjusted from the remote control.

Press the CINE FLTR or LATE NIGHT button to display the current setting (On or Off). To change the current setting, press the same button again.

Remote controller

Remote controller

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents HT-R420 Important Safety Instructions AvisFor U.S. models PrecautionsPower For Canadian modelsAmplifier Features FeaturesSupplied accessories FM/AM Tuner FeaturesUsing the Remote Controller Before Using the HT-R420Setting the Voltage Selector Worldwide model only Remote control sensor HT-R420 Standby indicator 30˚Index to parts and controls Index to parts and controls Tape IN/OUT Remote ControlRear panel Antenna 14= Mode buttons Remote controllerPreset 2/3 button @ Adjust 2/3 buttonConnecting to audio/video equipment Before connectingVideo Connection Formats Connecting to audio/video equipment Video cassette playerSatellite tuner, LD Player*5, etc. Video Positioning speakers/Connecting speakers Standard speaker placement of the speaker system aConnecting to the speaker system a Positioning speakers/Connecting speakersHow to connect to the speaker terminals Connecting to the speaker system BConnecting antennas Connecting the supplied FM and AM indoor antennasConnecting an Outdoor AM Antenna Connecting antennasConnecting an Outdoor FM Antenna Strip and prepare the 75 ohmPower off function Connections for remote control zPower on/ready function Direct change functionEnjoying music or videos with the HT-R420 Speaker setup Setting the crossover frequencyPress Speaker Adjust twice Speaker setup Subwoofer Mode Setting the subwoofer mode Press Subwoofer Mode on the unit→ Subwoofer Mode 1 Default Adjusting each speaker’s relative volume balance Test toneChanging the default settings according to your connections Listening to the radio Tuning into a radio station Press TunerTuning in a weak frequency only for FM stations There are two ways to select radio stationsPress Tuner to switch the input source to the tuner Presetting radio stationsSelecting preset stations Listening to the radioVarious functions common to all the sources Muting the sound remote controller only Press MutingListening through headphones Before operating the SP A/SP BUsing the sleep timer remote controller only Press Sleep Various functions common to all the sourcesChanging the display Press Display May be in a Setting the input signal formatThese buttons Slightly differentBefore operating the Direct or Using analog multi channel inputEnjoying multi channel sources CH SEL Level 5/∞Enjoying the listening modes Press one of the listening mode buttons Selecting the listening modeBefore operating the remote controller Input source and available listening modeAudio adjust function Before operating the remote controlUsing the audio adjust functions Audio adjust function Recording a source Input selector buttonsVideo Camera Using the remote controller with your other AV components Entering the manufacturer’s code RC-518M onlyNumeric Using the remote controller with your other AV components ManufacturerCable Satellite Use the remote controller’s mode buttons i.e Using the RC-518MPoint the remote controller at the HT-R420 Use the input selector buttons to select anVCR mode VCR CD modeTape mode RCVR/TAPE VCRTV mode TV Cable mode CABLE/SAT Satellite mode CABLE/SAT Cable SATTroubleshooting Amplifier Remote controller Symptoms Causes Remedies PagesTuner TroubleshootingSymptoms Causes Remedies OtherVideo Section SpecificationsAmplifier Section Tuner Section
Related manuals
Manual 96 pages 51.33 Kb
Top Page Image Contents