Mitsubishi Electronics FL7000U user manual Support for the PJLink function, EN-16

Page 16

Support for the PJLink™ function

This projector supports standard protocol PJLink™ for projector control and you can control and monitor projector’ s operations using the same application among projectors of different models and different manufacturers.

To use this function, set the PJLink™ certification properly according to the setting of the PJLink™ application to be used. (See page 11.)

Supported commands

The table below shows commands to control the projector using the PJLink™ protocol.

Command

Description

Remark (Parameter)

POWER

Power control

0 = Standby

 

 

1 = Power on

POWR?

Inquiry about the

0 = Standby

 

power state

1 = Power on

 

 

2 = Cooling down

 

 

3 = Warming up

INPT

Input switching

11 = RGB1

INPT?

Inquiry about input

12 = RGB2

 

switching

21 = VIDEO

 

 

22 = S-VIDEO

 

 

31 = DVI-D

AVMT

Mute control

30 = Video and audio mute disable

AVMT?

Inquiry about the

31 = Video and audio mute enable

 

mute state

 

ERST?

Inquiry about the

1st byte: Fan error, 0 or 2

 

error state

2nd byte: Lamp error, 0 to 2

 

 

3rd byte: Temperature error, 0 or 2

 

 

4th byte: Cover open error, 0 or 2

 

 

5th byte: Always 0

 

 

6th byte: Other error, 0 or 2

 

 

0 to 2 mean as follows:

 

 

0 = No error detected, 1 = Warning, 2 = Error

LAMP?

Inquiry about the

1st value (1 to 5 digits): Cumulative lamp

 

lamp state

operating time

 

 

2nd value: 0 = Lamp off, 1 = Lamp on

INST?

Inquiry about the

The following value is returned.

 

available inputs

“11 12 21 22 31”

NAME?

Inquiry about the

The projector name set on the ProjectorView

 

projector name

Setup window is returned.

INF1?

Inquiry about the

“MITSUBISHI” is returned.

 

manufacturer name

 

INF2?

Inquiry about the

“FL7000U” is returned.

 

model name

 

INF0?

Inquiry about other

No other information is available. No parameter

 

information

is returned.

CLSS?

Inquiry about the

“1” is returned.

 

class information

 

This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands defined by PJLink™ Class 1, and the compliance has been verified with the PJLink™ standard specifications Version 1.0.

(Note)

The above-mentioned control may not be performed correctly or the monitoring data may not be obtained correctly in the following conditions:

During standby

During zoom/focus adjustment

During lens shift adjustment

• During input source switching

• During auto position execution

During AV mute

During command processing

Before the splash screen disappears after the power is turned on.

During zoom/focus adjustment, lens shift adjustment, AV mute, etc., it may take approx. 5 seconds to receive a response to a command.

Use 1 controller to control/monitor 1 projector.

For how to control/monitor using PJLink™, see the operation manual of the PJLink™ application you use.

When you monitor the projector’s operating state using this function by issuing inquiry commands successively, issue an inquiry command after receiving the response to the previous inquiry command from the projector.

For the specifications of PJLink™, access to the Web site of Japan Business Machine and Information System Industries Association (JBMIA). (http://pjlink.jbmia.or.jp/english)

EN-16

Image 16
Contents LAN Control Utility Contents Preparation/SetUp Preparation before using the network functionMajor functions System requirementsInstallation Preparation/SetUpConnection EN-3How to remove Projector-Control Device Installer EN-4Setting the IP address of the projector EN-5When using a Dhcp server EN-6When not using a Dhcp server EN-7Telnet setting EN-8Setting the password Password Setup EN-9Setting the LAN control LAN-Controlled Mode Setting the display language of ProjectorView languageEN-10 Save and exit Setting the PJLink certification PJLink certification ModeEN-11 Using the ProjectorView How to start upProjectorView EN-12ProjectorView main screen ProjectorViewEN-13 Mail notification function ProjectorView Virtual Remote controllerEN-14 ProjectorView Initial setting EN-15Support for the PJLink function EN-16Terms and definitions Support for the PJLink functionEN-17
Related manuals
Manual 8 pages 22.25 Kb