Mitsubishi Electronics EW270U Personalizing the projector menu display, Direct power off

Page 34

1.Repeat steps 1-2 above.

2.Press to highlight Volume and press / to select a desired sound level.

Standby Audio Out

Selecting On enables the function. The projector can output an Audio input signal when it is in standby mode and Audio input and Audio out jack is correctly connected to devices.

When the projector enters standby mode, the audio will be interrupted briefly. This is not a product malfunction.

Personalizing the projector menu display

The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance.

Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame.

Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position.

Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to select your language.

Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen.

Shutting down the projector

1. Press II POWER and a confirmation message displays prompting you. If you don't respond in a few seconds, the message will disappear.

2. Press II POWER a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector.

3. Once the cooling process finishes, the POWER indicator light is a steady orange and fans stop.

4.Disconnect the power cord from the wall socket if the projector will not

be used in an extended period of time.

• To protect the lamp, the projector will not respond to any commands during the cooling process.

To shorten the cooling time, you can also activate the Quick Cooling function.

See "Quick Cooling" on page 45 for details.

Do not unplug the power cord before the projector shutdown sequence is complete or during the 90-second cooling down process.

If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press II POWER again to start the projector after the fans stop and the POWER indicator light turns orange.

Direct power off

1.The AC power cord can be pulled out during the projector is on. To protect the lamp, wait about 10 minutes before re-starting the projector. (When you attempt to re-start the projector, the fans may run for a few minutes

to cool down. In such cases, press II POWER again to start the projector after the fans stop and the POWER indicator light turns orange.

2.To protect the lamp, do not shut down the projector while the POWER indicator light is blinking green after the lamp lights up.

3.Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without closing the menu, the setting data of the menu may not be saved.

4.If you shut down the projector while controlling the projector using the network function, the application software such as e-Control™ may fail. In this case, close the application software first. After the connection between the projector and the computer re-establishes, initialize the software again.

EN-34

Image 34
Contents EX240U/EW270U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Projector exterior view Kensington LockControls and functions ProjectorRemote control Magnifying and searching for details on page 26 forRemote control effective range Positioning your projector Choosing a locationWhen fine streaks are seen on projected images Obtaining a preferred projected image sizeEN-13 Front projection Layout of the projectorStandard 169 EX240UConnection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting a monitor Connecting Video source devicesTo connect the projector to a monitor To connect the projector to an Hdmi device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceOperation Starting up the projectorUsing the menus If you forget the password Utilizing the password functionSetting a password Entering the password recall procedureDisabling the password function Switching input signalChanging Color Space Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio EW270U EX240UEN-28 Setting the User 1/User 2 mode Selecting a picture modePicture modes for different types of signals Optimizing the imageFine-tuning the image quality in user modes Using Wall Screen 3D Color ManagementTo cancel the timer, perform the following steps Setting the presentation timerHow to use the Timer On key? Locking control keys Adjusting the soundHiding the image Freezing the imageShutting down the projector Direct power offPersonalizing the projector menu display Standby Audio OutWatching 3D Content L RXGA60 If you are in a Dhcp environment Configuring the LAN Control SettingsSupervising and controlling by computer If you are in a non-DHCP environmentPress / to reveal How to Use Network Function Error Status DescriptionGlossary DhcpMain menu Sub-menu Options Menu operationMenu system BasicSystem Setup Blank Timer AdvancedDescription of each menu Save Settings Setting Brightness Contrast ColorColor Temperature TintAuto Power Off System Setup Basic menu System Setup Advanced menuPresentation Timer Blank TimerClosed Caption Enable Current System StatusMaintenance Care of the projectorLamp information Setting Lamp mode as LowSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Spare lamp for EX240U/EW270U VLT-EX240LPResetting the lamp timer EN-52 Indicators Power Temp Lamp Power eventsTroubleshooting Specifications Projector specificationsDimensions Timing chartSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation