Mitsubishi Electronics EW270U user manual How to Use Network Function, Error Status Description

Page 39

iv.Once set, access to the remote network operation page on this projector has been password-protected. To enable this function, check the box in front of "Enable" and type in your desired password in the New Password column and confirm the new password by re-entering the new password at the Confirm column. To disable password protection, uncheck the box.

v.Once set, access to the Tools page has been password-protected. Refer to step iv for how to use the password function.

• After making the adjustments, press the Send button and the data will be saved in the projector.

•Once the password is set, the Log Out button will display beside the Tools button.

•Write down your selected password in advance or right after the password is entered so that it is available to you should you ever forget it. If you forget the password, you will not be able to log in.

•The software is available in English language.

•When DHCP is turned on, there is a possibility of stopping the webpage connection. If this happens, please check the new IP address of the projector and enter the new address to connect again.

vi.Press Exit to go back to the remote network operation page.

4.The Info page displays the information and status of this projector.

i

iii

iii

ENGLISH

i.The information you entered in the Tools page will display here and these columns are empty when you use e-Control™ for the first time.

ii. When the projector is in abnormal conditions, the following information will display.

When the projector is in normal conditions or in any abnormal conditions other than the ones mentioned below, the Error Status column will be empty.

Error Status

Description

3: Lamp fail

The lamp fails to ignite or turns off during operation.

 

 

3: Over Temp

The projector temperature is too high or cannot be detected.

 

 

3: Fan Lock

The fan rotation speed cannot be set or detected.

 

 

1: Over Lamp Usage time

The lamp is still in use after the lamp warning messages display.

 

 

(3 = Error; 1 = notice)

iii.Press Exit to go back to the remote network operation page.

5.After pressing the button ‘Contact IT Help’, the HELP DESK window will appear at the upper right corner. You will be able to deliver messages to RoomView™ software which is connected to the same local area network.

For more information, visit http://www.crestron.com & www.crestron.com/getroomview.

How to Use Network Function

•When connecting a computer and projector with LAN, confi gure the both IP Addresses in the same network group.

•Confi gure the IP CONFIG correctly. If the settings are not correct, the communication may be unavailable. For the detail, consult the network administrator.

•When the Control By in the SYSTEM SETUP: Advanced > LAN Control Settings menu is selected RS- 232C, the LAN Control Settings function is not available.

EN-39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents EX240U/EW270U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Kensington Lock Projector exterior viewProjector Controls and functionsMagnifying and searching for details on page 26 for Remote controlRemote control effective range Choosing a location Positioning your projectorObtaining a preferred projected image size When fine streaks are seen on projected imagesEN-13 Layout of the projector Front projectionStandard EX240U 169To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionConnecting Video source devices Connecting a monitorTo connect the projector to a monitor To connect the projector to a Component Video source device Connecting an Hdmi deviceConnecting a Component Video source device To connect the projector to an Hdmi deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUsing the menus Entering the password recall procedure Utilizing the password functionSetting a password If you forget the passwordSwitching input signal Disabling the password functionChanging Color Space Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsEW270U EX240U Selecting the aspect ratioEN-28 Optimizing the image Selecting a picture modePicture modes for different types of signals Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Using Wall ScreenSetting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Freezing the image Adjusting the soundHiding the image Locking control keysStandby Audio Out Direct power offPersonalizing the projector menu display Shutting down the projectorL R Watching 3D ContentXGA60 If you are in a non-DHCP environment Configuring the LAN Control SettingsSupervising and controlling by computer If you are in a Dhcp environmentPress / to reveal Error Status Description How to Use Network FunctionDhcp GlossaryBasic Menu operationMenu system Main menu Sub-menu OptionsAdvanced System Setup Blank TimerDescription of each menu Tint Setting Brightness Contrast ColorColor Temperature Save SettingsBlank Timer System Setup Basic menu System Setup Advanced menuPresentation Timer Auto Power OffCurrent System Status Closed Caption EnableCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as LowSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampSpare lamp for EX240U/EW270U VLT-EX240LP Replacing the lampResetting the lamp timer EN-52 Power Temp Lamp Power events IndicatorsTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation
Top Page Image Contents