Mitsubishi Electronics EX200U user manual Operation, Starting up the projector

Page 19

Operation

Starting up the projector

1.Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied.

• Ask your installation specialist to provide an Earth leakage breaker. When you do

not use the projector, be sure to shut down the main power by the breaker.

•Please use the original accessories (e.g. power cord) only with the device to avoid possible dangers such as electric shock and fire.

•In order to ensure the safety in case of trouble with the projector, use an electrical outlet having an earth leakage breaker to supply the power to the projector. If you do not have such outlet, ask your dealer to install it.

2.Remove the lens cap. If it is closed, it could become deformed due to the heat produced by the projection lamp.

3.Press II POWER on the projector or remote control to start the projector. The POWER indicator light flashes green and stays green when the projector is on.

The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected.

(If necessary) Rotate the focus ring to adjust the image clearness.

•If the projector is still hot from previous activity, it will run the cooling fans for approximately 90 seconds before energizing the lamp.

•To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning it off.

•After II POWER is pressed, the image may flicker before the lamp becomes stable. This is not a product malfunction.

4.If the projector is activated for the first time, select your OSD language following the on-screen instructions.

5.If you are prompted for a password, press the arrow keys to enter a six- digit password. See "Utilizing the password function" on page 21 for details.

6.Switch all of the connected equipment on.

7.The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will be displayed until an input signal is found.

You can also press SOURCE on the projector or remote control to select your desired input signal. See "Switching input signal" on page 22 for details.

If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message 'Out of Range' displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 47 for details.

ENGLISH

EN-19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents EX200U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Kensington Lock Projector exterior viewProjector Controls and functionsMagnifying and searching for details on page 24 for Remote controlRemote control effective range Choosing a location Positioning your projectorObtaining a preferred projected image size EN-12 Front projection Layout of the projectorTo connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer ConnectionConnecting a monitor Connecting Video source devicesTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceStarting up the projector OperationUsing the menus Entering the password recall procedure Utilizing the password functionSetting a password If you forget the passwordDisabling the password function Switching input signalFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioOptimizing the image Selecting a picture modePicture modes for different types of signals Setting the User 1/User 2 modeFine-tuning the image quality in user modes 3D Color Management Using Wall ScreenTo cancel the timer, perform the following steps Setting the presentation timerHow to use the Timer On key? Freezing the image Adjusting the soundHiding the image Locking control keysPersonalizing the projector menu display Direct power offShutting down the projector Menu system Menu operationSystem Setup Blank Timer Description Description of each menuSetting Brightness Contrast Color System Setup Basic menu System Setup Advanced menu Change password EN-38 Care of the projector MaintenanceGetting to know the lamp hour Setting Lamp mode as LowSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampSpare lamp for EX200U VLT-EX240LP Replacing the lampResetting the lamp timer Light Status & Description Power Temp Lamp Power events IndicatorsTroubleshooting Projector specifications SpecificationsTiming chart DimensionsSupported timing for Component-YPbPrinput Replacement partEN-49 Mitsubishi Electric Corporation
Related manuals
Manual 49 pages 20.98 Kb

EX200U specifications

The Mitsubishi Electronics EX200U and ES200U are innovative and highly efficient solutions designed to meet the demands of modern automation and control systems. Tailored for both industrial and commercial applications, these servo drives enhance performance while ensuring reliability and precision.

At the core of the EX200U and ES200U models is advanced motion control technology. These servo drives leverage high-resolution feedback systems to deliver exceptional positioning accuracy, which is critical in applications such as robotics, CNC machinery, and advanced manufacturing processes. The integration of Mitsubishi’s proprietary algorithms allows for real-time processing of motion commands, enabling smoother operations and reducing mechanical stress.

One of the standout features of the EX200U and ES200U is their versatility. These servo drives support a wide range of motor types, including synchronous and asynchronous motors, making them suitable for various operational demands. With scalable performance, users can easily adjust settings to match the specific needs of their applications, whether they require high speed or high torque.

Energy efficiency is another essential characteristic of the EX200U and ES200U. Both models are designed to minimize energy consumption without sacrificing performance. The incorporation of regenerative braking technology allows for energy to be recaptured during deceleration, contributing to lower operational costs and a smaller environmental footprint.

The user-friendly interface of the EX200U and ES200U simplifies configuration and monitoring. With intuitive software tools, engineers can quickly set up, program, and fine-tune the drives. The ability to interface seamlessly with Mitsubishi’s broader automation ecosystem enhances operational cohesion, allowing for standardized control and data analytics across multiple devices.

Safety is also prioritized in the design of the EX200U and ES200U. These servo drives come equipped with integrated safety features, including safe torque off and error handling capabilities that protect both equipment and personnel. Compliance with international safety standards further reinforces their reliability in industrial environments.

In summary, the Mitsubishi Electronics EX200U and ES200U servo drives represent a blend of advanced technology, user-centric design, and energy efficiency. With their impressive features and capabilities, they are well-equipped to handle the demands of contemporary automation, providing users with reliable and precise control for a wide array of applications.
Top Page Image Contents